Jump to content
SAU Community

Recommended Posts

Hi there, I have a question for those people using the emanage ultimate in there vehicles. What power are u making and what mods have u done to the car. I am curious because not many people seem to wanna tune them. I have got an atr43g3 turbo with 600 cc injectors and would like to see what maps and mods people have done to there cars etc. I would like to get a map off another car that is similar to mine if possible thank u all

Link to comment
https://www.sau.com.au/forums/topic/349601-emanage-ultimate/
Share on other sites

They are good for what you're paying for but wouldn't you want the stability of a stand alone ecu if you're going to push the car above 250kw? And as you said it's not worth using one as you are limited with tuners.

Just a tip if you decide to keep it, don't bother with a map sensor. Keep using an AFM as the map sensor tables (to eliminate the AFM) are a bitch to get right.

Im hopefully going to get about 280 thats my plan I already have the unit and in the car. I have asked around a few tuners and 2 said they are a piece of shit but didnt know anything about them. One of them didnt even know that u DONT use a hand controller on them as they use a computer based software after that he said he would give it a go. The other 2 i contacted said they are a great piece of gear..........All i can gather is people just dont know how to use them Im really hoping that some one has my type of mods and i can get a rough map off them as its a bit of a pig to drive ( it currently has a remapped ecu for stock turbo fmic fp f/f exhaust ) so turbo very very laggy due to timing being retarded before boost comes on

I have one, only because there are no other ecu options like nistune. A good tuner can extract big power but it can drift a bit due to the stock ecu's mapping which is not a good idea at that level, and is one of the reasons I went e85 for safety. I have managed 300awkw so far.

Shame you aren't down in Melbourne, there are two tuners within a few k's of me willing to set them up, Trent (Status) and Cihan (Etuner), both very competent.

HI there I am aware of Trent as i have read his thread from what i can see he does a very good job I installed the emu and have figured how to change the afm and injector sizes and increase the lag time so it idles good. Its a bit hard up brissie way where some tuners will give it a go but not actually know how they work ( Oh please oh please does someone have the same mods as me lol )

I am forced (unhappily, but noone in the country can find an alternative..) to use one.. and my car setup will/is _SIMILAR_ to yours, but my car runs so poorly you surely don't want a map of this.

I was wondering if the piggyback is the reason it (mine) is so laggy, that or a really half-assed tune. :P

I am forced (unhappily, but noone in the country can find an alternative..) to use one.. and my car setup will/is _SIMILAR_ to yours, but my car runs so poorly you surely don't want a map of this.

I was wondering if the piggyback is the reason it (mine) is so laggy, that or a really half-assed tune. :P

Must be the tune, the Ultimate is very capable in the right hands. Perhaps tuning the low end yourself is an option?

get a wideband, connect it. learn to use auto tune.

if you get familiar with the data logger you can get on the PPo2 website (http://ppo2performance.com/docs/?cat=4) and get the baseline software which takes your data logs and helps you fine tune your fuel map. its a very smart piece of kit for the emanage. i was one of the testers in its early stages and this guy has spent a LOAD of time and effort getting it right. keep in mind its still in its beta stage.

  • 3 weeks later...

I have one, only because there are no other ecu options like nistune. A good tuner can extract big power but it can drift a bit due to the stock ecu's mapping which is not a good idea at that level, and is one of the reasons I went e85 for safety. I have managed 300awkw so far.

Shame you aren't down in Melbourne, there are two tuners within a few k's of me willing to set them up, Trent (Status) and Cihan (Etuner), both very competent.

What do you mean 'drift'? Is this because it only adjusts the stocks ECU's fueling and timing rather than having 'fixed' maps? The stock ECU is still free to do what it wants?!mellow.gif

It will be better than stock, but it won't be good enough. Save the money on buying it and get a nistune and get that installed and tuned. The different will be quite large, it will also be far easier to tune and you will have a larger base of tuners to choose from.

What do you mean 'drift'? Is this because it only adjusts the stocks ECU's fueling and timing rather than having 'fixed' maps? The stock ECU is still free to do what it wants?!mellow.gif

Yeah but the stock ecu doesn't use many correction maps or on the fly tune adjustments so you can get away with piggy backs most of the time, still better to go full aftermarket/nistune though.

Edited by Rolls

I had one on my r33 gtst and it was great. For the price at that point in time I couldnt argue and the results were definately worth it. Now with the GTR I will either go NISTUNE or PFC.

It will be better than stock, but it won't be good enough. Save the money on buying it and get a nistune and get that installed and tuned. The different will be quite large, it will also be far easier to tune and you will have a larger base of tuners to choose from.

Yeah but the stock ecu doesn't use many correction maps or on the fly tune adjustments so you can get away with piggy backs most of the time, still better to go full aftermarket/nistune though.

Nistune is just 16x16 maps and no provision for individual cylinder trims though? Slow as well only 8 bits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...