Jump to content
SAU Community

Power Window Motor Replacement/clean

180 wanabe
 Share

Recommended Posts

Seano350GT Veteran

Seano350GT

Posted
Posted

My driver's side window is slower to wind up than the passenger side, but they both go down at the same speed. The "auto" feature on my window does not work on the driver's side, but does work on the passenger side. Also when you close the door and the window moves up a little bit, that does not happen with the drivers side but it does with the passenger side.

Will pulling apart the door trim and cleaning the driver's side motor fix all the issues or would it be smarter to just buy a whole new motor?

The Max Mentor

The Max

Posted
Posted

It's definitely best to do things properly and in this case, replace the motor as Chris suggested. It's not like Nissan's window motors are built poorly like Ford's. Those things definitely need modification to make them actually reliable, much like what I did to my BA wagon's lock motor/mechanism.

russky Collaborator

russky

Posted
Posted

I haven't read all of the posts above, but I thought I'd share my experience: the window motor stopped working too. First it was half working, then completely stopped putting the window down. Went to Nissan who stated I require the whole motor to be completely replaced. They quoted over $1k for the job.

After speaking to an electrician, I was informed that the motor inside just likely needs a bit of cleaning. There are plenty of instructions that can be found online on how to get to the motor. When you disassembly the motor, you may realise that it consists of moving parts that just get worn out and need cleaning for better contact (research a little about how a motor operates if in doubt). After a good clean of the coils etc, it works great so far.

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

tell that to the customer that just left my shop. he was following this thread and had the drivers motor FAIL in the down position.

forget trying to save them. when they start not going up all the way or falling to half way - replace it.

I wish I had the motor for this car on hand. would have saved him a trip back here.

vee35 Enthusiast

vee35

Posted
Posted

I know I am living on the edge, but a few weeks ago, mine jammed in the down position and it was a long cold drive from where I was to home. I searched the internet for some clues, and found it was a common problem. I found one post where someone just whacked their door, and it worked, so I gave it a go. It worked. The window went up, and kept working for a few weeks, before it happened again. And another whack, and it was back in action.

This is no permanent fix in my eyes, but if you get caught out, give it a go to get home. And we are not talking too hard, and it was on the outside of the door, I did it from sitting in the drivers seat, with my arm out the door.

The Max Mentor

The Max

Posted
Posted

I haven't read all of the posts above, but I thought I'd share my experience: the window motor stopped working too. First it was half working, then completely stopped putting the window down. Went to Nissan who stated I require the whole motor to be completely replaced. They quoted over $1k for the job.

Typical of a dealership.

After speaking to an electrician, I was informed that the motor inside just likely needs a bit of cleaning. There are plenty of instructions that can be found online on how to get to the motor. When you disassembly the motor, you may realise that it consists of moving parts that just get worn out and need cleaning for better contact (research a little about how a motor operates if in doubt). After a good clean of the coils etc, it works great so far.

I have yet to come across a motor of any application that only needed a cleaning to last for years upon years. If something gets worn out (not dirty), then cleaning alone is not restoring the motor back to its original condition or even close to it. The best you can hope for are slightly worn brushes but not too far gone. All you've really done is prolonged the cancer patient's life expectancy as opposed to curing it. Not the best analogy but you get my drift.

In the end, it's all well and good if it's your own car because you only have yourself to blame if you find yourself having to fix it again down the track. In Chris' case, he runs a reputable business and it would look pretty bad for him to send away a customer with a cleaned motor only to have it come back again not long after with the same problem. Besides which, why do the same job twice because you took a gamble?

Chris Rogers Grand Master

Chris Rogers

Posted
Posted

tony,

i think we are trying to re-educate the 'educated'

there is no 'fix' for this . what i have found over the years is a lot of bad information on forums that claim to fix things when they really do nothing.

general rule for a v35, if a door acts up have $1 k per door handy if you cant chnge the bits out yourself.

again there is not a quick fix for this problem..

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...