Jump to content
SAU Community

Recommended Posts

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

no real information to update...

your welcome Charles

and Carlo they are top feed high imp, Heslo has just bought a set so somehow they must suit RB26dett's

as soon as the supplier puts together our price's i will update i do have small update he told me today he also sells fuel pumps and gave me retail prices on them, unfortunately i left the paper work at work but ill go from memory

Bosch 044 $215

Bosch 040 $187

Walbro Int. $136

Walbro Ext. a little dearer than $136 but cant quiet remember he will supply me with new group buy prices on the fuel pumps also

all items pumps and injectors come with a full 12 months manufacturer's warranty and 100% authentic no Chinese copies

probably not PM sent i may extend this GB as i don't want to rush information but i wanted to get it started

and i will make a thread in the GB section and put a link for everyone to go register on

Hmm i found this bloke on EBAY, looks like he also sells Siemens 890cc Top feed Low Impedance EV1 Injectors for $79 each.

Following Stats:

Static Flow Rate: 83.2 lb/hr = 10.87g/s = 888 cc/min (+-/ 4%)

Dynamic Flow Rate 2.5ms PW @ 100Hz: 19.5mg/pulse (+/-4%)

Coil Resistance: 2.35 Ohms / Low Impedance / Low-Z (Peak/Hold driver circuit required)

Spray Pattern: Pencil

Connector: Minitimer (Bosch EV1)

Only downside i could see here is you would need a 14MM fuel rail.

Edited by ZED X

hahahah did you note the seller, did you note in post #1 where i said parts are coming from :D

and RB20,25 want high impedance GTR use low impedance and Heslo didn't get back to my txt

and the 80lb Siemens injectors on his webshop are dearer than he quoted us already :D :D

Steve - what size RB25 injectors can you get? Currently using S15 450'cc and dont want to go up too big, ie 550's, 600's etc

Whats available?

cheers mate..... if i upgrade the injectors I'll definitely (finally) bolt on the exh.manifold and perhaps look at a greddy-copy intake plennum.

one last tune perhaps :)

this i might be interested in steve.

aye - is it wideband, and compatible with nistune/pfc?

These innovate units work with nistune for sure, and look quite decent

http://www.innovatemotorsports.com/products/db.php'>http://www.innovatemotorsports.com/products/db.php

http://www.innovatemotorsports.com/products/lc1.php'>http://www.innovatemotorsports.com/products/lc1.php

Thats what I'm semi keen on... does that one talk to nistune ?

-D

6. What Wideband support is there?

Currently NIStune supports the following Wide Band units:

TechEdge 1.5 and 2.0

http://www.techedge.com.au

Innovate LM1 and LC1

http://www.innovatemotorsports.com

AEM UEGO

http://www.aempower.com

Zeitronix

http://www.zeitronix.com

PLX Devices (R Series)

http://www.plxdevices.com

MOTEC PLM

http://www.motec.com.au/plm/plmoverview

Just Another Wideband

http://www.14point7.com

VEMS Wideband

http://www.vems.co.uk

DLP Design A/D Converter

http://www.dlpdesign.com/usb/io8.shtml

These units connect to your laptop via the serial port (or USB port when using serial-USB adaptor). These units output data to allow NIStune to monitor your Air Fuel Ratios from their sensor, and some produce auxillary inputs for connecting other sensors which can display and log inside NIStune.

NIStune provides several internal utilities to make the most of your Wide Band

- Dyno Mode AFR graphing against RPM

- Real time AFR and auxillary map display (minimum AFR, maximum AFR and current AFR against the fuel map)

- Logging and playback of AFR

yes the unit is wideband

looking into if its a nistune compat but i dont see why as it has its own box to read the O2 sensors that comes with it

oh :( the whole kit the guage i posted and 02 bit is $504

that below is the rest of the kit

http://www.dynojetwb2.com/images/products/wb2_kit_1.jpg

Brendan if you only want 500cc i can get the 52lb/h injector there around 535cc

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...