Jump to content
SAU Community

Coolant Leak From Pipe Under Intake - Whats It Called?

damono

By damono,
in General Maintenance

 Share

Recommended Posts

damono Proficient

damono

Posted
Posted

hello.

I've got a bad coolant leak from what seems to be a metal pipe that comes off the block, under the intake (on the drivers side).

I need to find out what the part is so I can order one, then whats the best way to tackle it. Im guessing it would be easier to get it on a hoist, but dont have access, im guessing ill have to take the whole intake off to get to it.

It feels like the metal pipe is a 90degree elbow, then goes onto a standard coolant hose. Sorry cant be more specific, havent had a good look at it myself yet...

Any ideas?

tm_r33 Experienced

tm_r33

Posted
Posted

its the thermostat housing pipe. Order a new thermostat. Get genuine. Buy a tube of good quality rtv silicon gasket maker.

Take hose off. Unbolt pipe. Change thermostat. (your doing this because you might as well while u have the pipe off). Clean old gasket from both block and pipe. Apply gasket glue to both surfaces. Allow 15 mins cure. Put pipe back in position. Bolt back up. Put hose back on.

Would be a good idea to drain coolant before u start.

once back together you can flush it brfore u refil with colant if you like.

So probably but coolant also.

tm_r33 Experienced

tm_r33

Posted
Posted

You can buy a gasket for the thermostat housing but ive had plenty of luck using liquid gaskets (rtv silicon gasket glue).

buy a genuine thermostat from nissan parts. Cheap repco ones can give poor results. They dont seat properly and they dont open and close as reliably as genuine.

Thermostat maybe 50 bucks.

gasket maker maybe 15 bucks.

coolant... All depends on what u buy. A concerntrate from repco will do the trick.

damono Proficient

damono

Posted
  • Author
Posted

Thanks mate,

I just had a bit of a feel around and look and it does seem to be the thermostat housing where its leaking from, I thought it was another pipe coming off the block below the thermostat housing. Thats a relief.

If the thermostat housing itself needs to be replaced, any ideas where and how much i'd be looking at?

damono Proficient

damono

Posted
  • Author
Posted

Could be. Hard to tell from where i'm looking. Does the heater hose/pipe come off the block, behind the thermostat housing, towards the firewall?

Repco or supercheap auto a good source for the heater hose/pipe or thermostat housing?

tm_r33 Experienced

tm_r33

Posted
Posted (edited)

Thermostat housing is just a cast alloy bit of pipe. Nothing can really go wrong with it. Would certainly be very rare or even unheard of if one was to split or crack from normal use.

It will just be where it seats against the block that the gasket is leaking or even where the hose slides over the housing that the hose is a bit perished and leaking.

Does the hose on this pipe u speak of go straight to the radiator? and its farely larger diameter hose? if so then yes its the thermostat housing.

Edited by tm_r33
Nur33 Mentor

Nur33

Posted
Posted

Yes there is a heater hose that comes from the thermostat housing and the block (well on a RB26 it is RB25 should be the same). Here's some pic's i tried to clear it up for you to make it easier to understand. Hope this helps you.

post-56933-0-79184900-1296648799_thumb.jpg

post-56933-0-45224000-1296648822_thumb.jpg

damono Proficient

damono

Posted
  • Author
Posted

Yeah, I know the thermostat housing, not sure if its coming from the base of that where it joins to the block, or the heater hose that comes from the block behind it.

If i were a betting man, i'd probably say its coming from the heater hose/pipe. I think ill have to take off the intake on the weekend and check it out. Seems like a bit of a jerk of a job to get the intake off tho :/

Thanks for all the info guys, been heaps of help!

Nur33 Mentor

Nur33

Posted
Posted

No worries mate give us a yell if you need more info, but i would be leaning towards a heater hose, i've had one fail one me before so i repalce them all with silicon hose kit, bit of a bastard to do but hey these cars are getting a bit long in the tooth nowthumbsup.gif

Nur33 Mentor

Nur33

Posted
Posted

yeah that depends i guess on how old it is and how much corrosion its been subjected to, you need to pressure test the cooling system without the engine running and see if that makes it show up more clearly.

damono Proficient

damono

Posted
  • Author
Posted

Awesome. Thanks again for the info buddy, ill get onto it on the weekend. The amount and speed it was leaking when under pressure, I think it will be pretty obvious when I get the intake off and have a good look at it. From memory, even under no pressure when I fill the radiator, it leaks from the spot.

jpoc_noel Apprentice

jpoc_noel

Posted
Posted

that ill be the heater hose and the easyest way is to whip off the starter motor and it's above there, and it's bloody tight to do too, also you'll get coverd in coolant too because it's below the block

  • 2 weeks later...
simpletool Mentor

simpletool

Posted
Posted

Change all the hoses now. There is about 11 down there, it only takes 1 to fail and it could be your head gasket. I posted a diagram of all the hoses under there on these forums before.

The diagram is on my external drive at home...sorry.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...