Jump to content
SAU Community

Recommended Posts

I picked up a brand new forged rb30 recently for an amazing price and I'm pretty excited about it, except the fact they O-ringed the block. They included a custom copper headgasket but I'm afraid it's going to leak and give me trouble.

I've been looking around I've found a few options

Use the copper head gasket and steel wire O-ring

Use MLS/stock paper gasket with copper wire O-ring

Use no wire and a MLS gasket

Use copper wire to fill the O-ring groove but not stick above the level of the block.

If anyone has experience with O-ringed RB's please let me know

The car is a r32 GTR that is mostly a track car and sees a bit of street driving, power is going to be in the 700-800whp range on E85.

Link to comment
https://www.sau.com.au/forums/topic/352641-o-ringed-block-gasket/
Share on other sites

GTRNUR has experience with this from his open deck engine.

When I last looked at doing it, the best way seems to be a standard headgasket with the copper O rings. You get the awesome sealing for water and oil from the standard gasket as it can take up the most irregularity in flatness and the O ring seals the cylinders near perfectly.

Otherwise next best would be your MLS with the copper O rings.

You could PM GTRNUR and ask for his advice.

GTRNUR has experience with this from his open deck engine.

When I last looked at doing it, the best way seems to be a standard headgasket with the copper O rings. You get the awesome sealing for water and oil from the standard gasket as it can take up the most irregularity in flatness and the O ring seals the cylinders near perfectly.

Otherwise next best would be your MLS with the copper O rings.

You could PM GTRNUR and ask for his advice.

+1

in the turbo bmw world where bore spacing is much closer than the rb and flatness causes issues with MLS gaskets, stock gaskets with copper ring sare popular as they have troubles with blowing gaskets between cylinders

Finally back online again after the cyclone!

Have you got any data for the depth of the o-ring grove and know what diameter the wire ring is? You need to take a few measurements.

I havent used copper rings in my engine. They are stainless, and I use a standard gasket with them and a spray on coating of hylomar. The general rule is 1/6 to 1/4 of the head gasket is how far you should have the o-ring protrudeing from the top of the block. Superglue them into the block to stop them moving when the gasket is put on as well, or they can tend to move. I use a product called ZAP which is an ultra thin superglue that you get from hobby shops.

Definatly use a few coats of hylomar on the gasket if your using a steel or copper gasket. You can probably get away without it with a standard gasket but really why risk it when the head is off.

On another tangent, Ive used copper head gaskets in my VW engines (which has basically the same cylinder sealing principals as a sleeved open deck engine). The trick with the vw's is to use a propane torch to heat the gasket up to a cherry red (done with them laying flat on a piece of alloy sheet), and then let them air cool. This softens/aneals the metal, so it better takes up deformaties in the two sealing surfaces.

This tracks with what r33_racer says, with having a copper o-ring seal to the mls headgasket. I'd be very nervous about using steel on steel with this approach though as the steel will not compress, so copper only with MLS. I'd lean towards 1/6th exposed o-ring height as well. If the o-ring distorts the gasket too badly, the gasket will leak all over the place, coolant in oil etc.

Most MLS gaskets have some sort of o-ring arrangement built into the combustion area anyway. Either as part of the embossing or as an o-ring that is between the MLS layers. Have a read about what Nitto do. The idea is to have a greater sealing pressure concentrated around the combustion chambers. Both o-ring blocks and MLS gaskets do this the same way. The difference is that the standard gaskets seal much better than a MLS gasket, and will tolerate far more surface distortion before the develop a leak.

bit of extra protection againist blowing out the gasket i guess. well the old engine lasted around 60,000klm with a hard time and when it was stripped down to fix a broken oil squirter it was still sealing perfectly.

Do you guys think a stock headgasket+steel oring would be a good setup for a track car? What is the thickness is a stock head gasket and how much stick up l do I want out of the oring? Do I need to worry about where the oring meets the factory headgasket?

The steel o ring + stock headgasket is looking like the best option right now.

In theory metal transfers heat better from the head to the block, so copper does that better than MLS steel, and steel better than stock.

But oil cooling is where most high reving track engines suffer anyway, due to oil spray to the bottom of the pistons mostly doing what its designed to do. That being pulling heat out of the piston crown.

The best advice I can offer is to go an talk to someone that builds RB track engines for a living and have them put together a setup for you. Racepace for example. Trying to do it 'successfully' as a first time project is a lot to expect and will often end in tears or great expense, probably both.

Also are you serious about your 700-800whp? To build an engine like that for track you definatly want an experts advice. That level of power tends to break everything else in the driveline like a twig so be prepared to open the wallet. And you'd better be able to drive better than Mark Scaife too, because the Group A cars didnt make that much power.

If you want the engine to last more than a day you will need a good $40K+, not counting driveline. Even if you have all the tools and all the skills to do the assembly and tunng yourself, its a $30K project easily. There are a few cars for sale at the moment that are built with similar power levels but they are not track ready yet. Whole cars tend to cost a good $120K upwards that can meet your 'requirements'.

Im serious about the power. I've got everything in the drivetrain upgraded, built head, single turbo, big fuel system, dry sump, huge brakes. I'm not going to be running that much power all the time and will probably be on low boost most of the time.

Im up in Canada and there is nobody experienced with a gtr with this much power on the track. I've talked to lots of people in the know overseas but I dont like bugging them all the time so I thought I would ask here first.

Well here's my suggested thoights for the bottom end:

Consider a partial grout fill, to just above the welsh plugs. This is done after you acid wash and before you bore the block, and before all machining work.

Drill and slot the mains to support RB26 bearings.

ACL race series RB26 mains and RB30 race series rod bearings.

Shave the cradle 0.001" and fit and ARP main stud kit. Torque to spec and then align bore to round. Aim for a bearing clearance of at least 0.003 to 0.0035" on the mains.

Carillo or pauter rods, again aim for 0.003 to 0.0035" clearance. 22mm gudgens would be a good idea.

Have your head CC'd and do your CR calculations based on a 0 deck and get a custom piston with an RB26 dome profile to suit your target CR. Eg 9:1 needs a 5-6cc dome depending on whats done to your head. Use a good piston like a CP or wiseco, 22mm gudgens would be a good idea as well.

Have the crowns ceramic coated and the skirts moly coated.

Follow the manufacturer settings for the ring gapping when filing the rings to fit the bores.

I'd be leaning towards 12mm ARP head studs, but since that modification requires drilling and tapping the block, you may as well go for 1/2" and have thread inserts put into the block as well. If you go 1/2" you will also need custom dowels to locate the head to the block. Some will say that is over engineering but they all say that till it breaks is my theory.

Fit your head studs and torque plate, and bore to piston spec sheet clearance. 87mm max bore unless you want to entertain sleeving, which will open a bunch of other options. You must use a torque plate, especially with the ARP head studs as the bores go very out or round with the extra torque the 1/2" studs can pull on the block.

Measure deck height in cylinder 1+6 and level shave the deck of the block to achieve a 0.000" deck on all cylinders, giving you a 0.047" deck height with the 1.2mm gasket.

Drill and tap threads into the oil galleries at each end of the block, and use tapered plugs with thread sealer when assembling. This is necessary to ensure your oil plumbing is 100% clean. If you are using a standard RB30 crank, have it drilled and grub screwed as well. Use a medium loctite on the grub screws when assembling. Wide colar fitted to the crank snout isnt needed with the dry sump, so dont machine the standard one off the crank.

Since you have a decent external oil pump you will need to experiment with the oil flow/gearing requirements that will allow you to achieve about 10psi/1000 RPM you intend to use. This will require more flow than the average engine due to the increased engine clearances. I presume you have one scavenge from the back of the head and two from the sump with a 4 stage pump. This is the most common approach.

Also do a search for the oil control thread here somewhere on the forum, and determine what restrictor setup you want to run. A blocked rear and 1.5mm front is pretty standard.

As for the head gasket, I'd recommend a standard gasket, but also consider having your head o-ringed to match the block with a w-ring arrangement. One ring fits inside the other when it crushes the gasket. This with hylomar on the gasket creates the ultimate seal for your fluids and combustion. It will never blow out.

This is just my opinion, for what its worth. Im no expert and have learned what I have from others that shared their information and from breaking a few things along the way. If you cant get this machining done locally in Canada (ie torque plate honing) properly, you should just box up your head and block and send the lot to RIPS and have them do the whole build for you. If you can afford a build like this, freight to New Zealand and back is a drop in the ocean as far as money is concerned.

  • 5 months later...

How do you drill and slot the mains for rb26 bearings?

I've been changing a lot of things with this setup and now I'm onto bearings. Can I just modify the rb30 main bearings for better oiling?

Im trying to avoid machine work as I just discovered the mains have .0015 clearance and I need to open it up. I was hoping to find some bigger main bearings and avoid machining and having to re-nitride my crank

Edited by Super_Dude

He means grooving the main bearing bore so oil flows out the oil feed hole and fills the groove or slot and feeds up through the rest of the holes in the shell. This is also sometimes referred to as annular grooving.

You can get 0.001" undersize bearings. So you could eseentially get 0.0025" with those bearings without touching the crankshaft journals. The ACL bearings have an X prefix after the code to indicate they are 0.001" bigger in oil clearance over standard.

2mm would be plenty, but check an RB26 block with a vernier depth gauge if you can get your hands on it. RB26 and RB30's use the same dimesion bearings, the only difference is that the 26 has the oil groove to provide better oil flow to the mains.

Regarding your mains being too tight, have you worked out where the clearances are too big? What are the crank dimensions? Make sure your micromoters have been certified as well, its easy for them to become 0.5 to 1 thou out if someone has dropped them.

You need to install your main stud kit, torque it to spec and have a machine shop tunnel bore/skim the main bearing saddles a little. Then the main bearings are re-installed and measured until you achieve the 3-3.5 thou bearing clearance. Remember your bearings crush a little when the cradle is torqued to spec. Align/tunnel boring the mains reduces bearing crush a little and increase oil clearances.

Don't use an N1 pump if you are going to run main clearances this big. Im thinking Tomei or external oiling only, otherwise crank movement will smash the pump.

We used plastigauge to check the clearences so Im not sure where it is tight\loose if it is out of round. The mains were tunnel bored before i got it and the crank just had a polish and check before we plastigauged it.

The oil pump is a 4 stage weaver. With the extra flow will it makeup for the lack of 26 mains?

If a mod finds this maybe it should be moved to the rb30 forum

You should really measure it with a mic and dial bore gauge so you can check it at a couple of different spots to find out where it is tight.

The 4 stage pump will shit it in for flow. However, you may just need an upgraded pressure relief spring. I assume you are running the pump around atleast 1/2 engine speed?

I think the 26 main bearings are supposedly 1mm wider then rb30 main bearings. Not that it really matters. Also the groove depth in the block, I think from memory it is something like 4-5mm deep. When we used to get it done to our rb30 blocks it was around 5mm deep at the lowest point and it would taper up as it got closer to the parting line each side.

You should really measure it with a mic and dial bore gauge so you can check it at a couple of different spots to find out where it is tight.

+1

Your crank could be out of round, or the cradle might not be from that block (or just be a bad match for it). Every main on the crank and block should be measured at 3 angles using a micromoter and telescopic gauge. Only then can you actually be sure your mains are round and that your bearing clearences are consistent. If you tell a good machine shop that this is what you want done, they should be able to do it for you.

Just torquing the cradle down and the associated twisting of the cradle that can happen is enough to give you an inaccurate reading.

To be honest the engine came assembled from an engine shop with a good reputation but we just wanted to double check everything.

Im going to find another engine shop to assemble and triple check everything with the proper tools. Im worried about machining the crank though as I will need to renitride but im considering having it all wpc treated after machining.

Im thinking I might not bother with the rb26 bearings as I dont know if I trust a machine shop and Im afriad they would screw something up. Im going to talk to the machine shop and see what they have to say about it.

While ive got your attention what should we run for thrust clearances?

Edited by Super_Dude

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...