Jump to content
SAU Community

Recommended Posts

im a maybe now, its going to be another late night up at Mt Barker

Dion, will work out getting the swaybar to you

Luke, i'll pop the ignitor in the car and take it to Mallala sunday, cos no doubt you'll pop your head out there ;)

Have you actually bought an R32 Tim?

the bank bought it for him...and he has to pay them back :domokun:

Thanks Steve, it goes pretty good. What spark plugs would you suggest for it? it's got 250.1 rwkw

I thought it had 205.1rwkw!?

you bought it from my cousin. f**king small world I tell ya.

Copper plugs would do the trick Chestnut :D

Is that who it was? He mentioned your name when we had a look at it. He asked me "Do you know Krishy?", I thought he may have been a relative of yours.

Fellas,

IM going to have to cancel tonight for me....

I have had some issues over in melbourne with buying another car and i wont get there in time as i am still in Melbourne now ... SPEWIN!!!!!pinch.gif

I will make sure next time im down to head down for a meet n greet.

Apologies

Matty

I wouldnt put a 2530 on a RB25, bit too small. 2530 on a RB20 however fits like a hand in a glove. On topic, I'm a maybe for tonight now.
If you do come down, don't forget the valley cover from the rb20 please

I wouldnt put a 2530 on a RB25, bit too small. 2530 on a RB20 however fits like a hand in a glove.

On topic, I'm a maybe for tonight now.

Bollocks ... I had an HKS 2530 on my R34 and it went like stink ... made a very lazy 230rwkw with only a very conservative SAFCII tune. Oh, and ZERO lag.

And 1) I have NEVER seen a stock turbo on an R33 run 215rwkw, and 2) if it magically did, for how long, and how hard were you wringing its neck?

As I said, my 2530 made a LAZY 230 behind an auto slush box, with no aftermarket timing/tuning (just an SAFCII), with standard injectors and fuel pump. Of course it could have made a shit-ton more if I would in more boost, got bigger injectors, bigger fuel pump, better tuning etc .... but that is not the point.

it did, and has done so now for 3 months or so, including the track day and plenty of driving. Just dont see the point of a turbo swap for such a minimal gain. thus why i went the 3076 to replace it

also in the 'post your rb25 dyno charts thread', there are a few freak motors making 225-230 with 15psi. yeah it may not last to long, but can be done. sometimes a set up just works

when i had my 33 it made 210rwkw on 12psi with stock turbo.... had power fc, front mount and exhaust

it made 185 before the power fc with a remapped computer from japan... i dont know what type was in there when i bought it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...