Jump to content
SAU Community

Recommended Posts

hello everyone,

I've got a 93 gts-t turbo auto, my ride is currently stock and I wanna modify it.

What do you guys recommend me to start with?

I'm looking for small mods to start with, that won't cost me a fortune. Yeah and it's got a cone shaped air filter installed thats it.

thanks for your time.

Link to comment
https://www.sau.com.au/forums/topic/353159-small-mods/
Share on other sites

hello everyone,

I've got a 93 gts-t turbo auto, my ride is currently stock and I wanna modify it.

What do you guys recommend me to start with?

I'm looking for small mods to start with, that won't cost me a fortune. Yeah and it's got a cone shaped air filter installed thats it.

thanks for your time.

Fuel Pump

3 Inch turbo back Exhaust with good cat

Front Mount Intercooler

Nistune

Link to comment
https://www.sau.com.au/forums/topic/353159-small-mods/#findComment-5659972
Share on other sites

What do you want out of the car?

What are your goals?

Have you done much research into what areas of the car can be improved?

What is your current budget and future budget?

Very hard to give you advice if we don't know all the details.

If you want more power, the first thing to do is change the restrictive exhaust system with a full 3" turbo back.

Have a look at the sticky in the Forced Induction section which will answer most of your questions.

Link to comment
https://www.sau.com.au/forums/topic/353159-small-mods/#findComment-5660114
Share on other sites

fuel pump?

shouldn't need that until ecu upgrade, but then again, you did list the ecu in your list of options.

Power wise, I would roll with, in order:

1. exhaust - bang for buck, this should enrich your hive with the most killer wasps. make sure it's a turbo back exhaust

2. front mount intercooler, and intake. I list these as one, as if you change your fmic, you will most liekly need to change your standard airbox to a pod, due to the change to piping

3. electronic boost controller - debatable, as you can only wind the boost up so much before the ecu kicks in with the fuel cut

4. ecu upgrade - nistune seems to be the flavour of the month. other proven methods include power fc and other well known stand alone units

5. turbo, injectors etc etc. depends on your budget, as now you are entering big bucks territory

on a side note, as you step up the power, braking, handling and drive train upgardes are highly recommended.

the other avenue you could take is improve your suspension and brakes as a starting point and build from there

decent set of coilovers with some nice brake pads will see a big improvement in your driving pleasure.

This would be the smart way to go, as it drastically improves the handling and braking of the car, but most people like to go the power way first and then catch up with the rest

Link to comment
https://www.sau.com.au/forums/topic/353159-small-mods/#findComment-5660152
Share on other sites

fuel pump?

shouldn't need that until ecu upgrade, but then again, you did list the ecu in your list of options.

Power wise, I would roll with, in order:

1. exhaust - bang for buck, this should enrich your hive with the most killer wasps. make sure it's a turbo back exhaust

2. front mount intercooler, and intake. I list these as one, as if you change your fmic, you will most liekly need to change your standard airbox to a pod, due to the change to piping

3. electronic boost controller - debatable, as you can only wind the boost up so much before the ecu kicks in with the fuel cut

4. ecu upgrade - nistune seems to be the flavour of the month. other proven methods include power fc and other well known stand alone units

5. turbo, injectors etc etc. depends on your budget, as now you are entering big bucks territory

on a side note, as you step up the power, braking, handling and drive train upgardes are highly recommended.

the other avenue you could take is improve your suspension and brakes as a starting point and build from there

decent set of coilovers with some nice brake pads will see a big improvement in your driving pleasure.

This would be the smart way to go, as it drastically improves the handling and braking of the car, but most people like to go the power way first and then catch up with the rest

I always go Fuel pump early on, most of them are pretty tired at this age.

Link to comment
https://www.sau.com.au/forums/topic/353159-small-mods/#findComment-5660514
Share on other sites

If you're just looking to make your caar a bit peppier you dont have to spend a fortune.

upgrade the intercooler to a front mount or a 34 gtt unit,decent zorst system, T boost controller and something to control air/fuel like safc 2 or nistune. Wind the boost up to around 10/11 lb and standard everything else will see a decent and very noticeable increase over stock after you have it dyno tuned.

As for the auto, Tellemf**kem, One of my lines is a 33 gtst auto and it has to be one of my all time fave cars. Finding one unmolested with low kays really bought home to me what a damn fine car a skyline is. :thumbsup:

  • Like 1
  • Nope 2
Link to comment
https://www.sau.com.au/forums/topic/353159-small-mods/#findComment-5668059
Share on other sites

Personally I'd make sure all the basics are taken care of first before putting more power into it. How many km's has the car done? Has the timing belt and waterpump been done? Engine oil recently been changed? brake fluid, coolant, spark plugs etc. Even doing a cleaning of the aac valve can make a minor improvement in responsiveness, depending how dirty it is of course.

Link to comment
https://www.sau.com.au/forums/topic/353159-small-mods/#findComment-5668114
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...