Jump to content
SAU Community

Recommended Posts

It'll be the light switch itself. Ive just repaired my switch as I was having exactly the same problem! No dash or parkers but had headlights and brake lights...

The little plastic spring loaded triggers in the switch that move the metal contacts wear down giving you the problem youre have right now.

You need to disassemble the switch and replace the worn spring loaded trigger so it once again contacts the metal switch.

Think of the bushes in an alternator, same concept.

There is a thread with pics if you do a Google search, think its on another Skyline forum.

Edit - Here you go http://www.skylinesaustralia.com/forums/topic/115618-r32-headlight-switch-and-dash-globe-replacement/page__hl__r32+switch

Edited by NSNPWR
  • 6 months later...

It'll be the light switch itself. Ive just repaired my switch as I was having exactly the same problem! No dash or parkers but had headlights and brake lights...

The little plastic spring loaded triggers in the switch that move the metal contacts wear down giving you the problem youre have right now.

You need to disassemble the switch and replace the worn spring loaded trigger so it once again contacts the metal switch.

Think of the bushes in an alternator, same concept.

There is a thread with pics if you do a Google search, think its on another Skyline forum.

Edit - Here you go http://www.skylinesa..._hl__r32+switch

I have this exact problem right now in my 1994 R32 GTR , any chance of what its worth for a new switch ? thanks !

Edited by sultanaz

K so I've received PMs regarding this...

Use the guide in the above link

And I paid $50 for another 2nd hand working switch cause I needed it at short notice..

interior.jpg

*pic not my car, random off google

Edited by 10 4
  • 1 month later...

It was the switch that was causing the problem, the switchs themselves are heaps shit, worst quality to be honest... it burnt my wiring too which was expected, so what i did was went to the wreckers and pulled wiring off a N14 pulsar which connected straight up. obviously had different colours but u do the obvious and take notice what wire goes where before u cut the burnt harness.

Heres a few pictures of the switch for anyone for the future.

bdummq.jpg

308v34p.jpg

Heres the burnt Wiring and Switch photos

2dw3s4.jpg

kc10fk.jpg

2lo2cea.jpg

And a Computerised Version listing of R32 Parts.

2a9txsg.jpg

Hope that helps. Got any questions then give a buzz.

Edited by sultanaz
  • 8 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...