Jump to content
SAU Community

Recommended Posts

  • Replies 192
  • Created
  • Last Reply

Top Posters In This Topic

oei!! wat Genisis ?!?? :)

I am in too!

usual routine, brisbane ppl meet at 7.45pm Milton Maccas and leaving at 8pm sharp.  I will be going down to Yoparata's place personally to make sure he's on time  :(

Yes, i also heard Genesis saying lets meet :sadam:

nah never found it, i may come out but it will have to be in dads ute or something?? its a ss, but its got something in common with whats happening to my car :) im so excited i pick my half cut up on monday, heard it running yesterday mmmmmmmm

Hey guys!

I am keen to sign up for my maiden voyage with you people on thursday night with a friend in one of his GTRs (hopefully) so if we are good to go, we will meet and greet at Milton Maccas at 7:45pm!

hmmm a NA 33 with a phatt V8 in it hey....sounds different....i like!! :nowigetit

Cheers

Hey guys!

I am keen to sign up for my maiden voyage with you people on thursday night with a friend in one of his GTRs (hopefully) so if we are good to go, we will meet and greet at Milton Maccas at 7:45pm!

hmmm a NA 33 with a !! :nowigetit  

Cheers

:wavey: See you on thursday. I hope you don't have to ride in the gtr though. It'd be nice to see your new gtst.

:wavey:  It'd be nice to see your new gtst.

ahhhh yeah,,,,

about that, complience is delayed another week because the parcel shelf was broken by the warfies when they stole my speakers!! So gettin another on tuesday and takin it down on wed,.....sooon Charly....soon..

Haro

Guys PM's will be sent out later this week which will include departure time, first stop and destination, only to those on the list though :P

But last time we had 15 people turing up we had like 30 :rofl: So hopefully it'll be a hum dinger again :)

R33Steve - I dont know where/when/if the brisbane people are meeting up but if you can make it down to Yatala by about 9pm, I got plans to leave between 9pm and 9:30pm.

So the drive from Milton to Yatala is only around 30mins so you should be able to make it down here fine.

Other than that, you might want to try PM'ing some of the other Brissie crew to see if they want to wait for you. (NA_R33, GenesisR32, yoparata, etc etc)

Hopefully see you there?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...