Jump to content
SAU Community

Low Mount Turbo

hooray

By hooray,
in Western Australia

 Share

Recommended Posts

hooray Collaborator

hooray

Posted
  • Author
Posted (edited)

ive got

hsd fully adjustable coilovers

work 17x8 with bridgestone potanza re01r 235/45/17 front and

17x9 with nexen roadstone 255/40zr/17

cheap rears but they wont last long anyway

305hp atw now on 14psi

chasing 300kw atw

Edited by hooray
SimonR32 Grand Master

SimonR32

Posted
Posted

Well take about 6% off your power everywhere because they added SAE correction (which ALLSTAR don't usually apply to RWD cars but I'll assume they did it on your graph because you asked for 400hp)... So that's about 380rwhp, then from a hub dyno you loose around 7% on top of that to a roller dyno dynamics so you are down to 355rwhp. So the same power as say a HKS GTRS on the same boost!

Next we will talk about boost response, well it's not really that bad considering the size of the wheels of the turbo (the 0.63 rear housing is helping a lot it seems). About the same as a T67 or a GT3076R 0.82 rear, mind they make about 430rwhp on the same dyno without correction on so the same response as yours but around 50hp more top end!

If you want to compare with my setup I make pretty much exactly the same power till 4000rpm and then a extra 150hp top end (mind you I cheat a little) :)

So in essence you have a turbo that makes the same power as a HKS GTRS with over 1000rpm less response or a turbo that has the same response as a GT3076R but with 50hp less top end...

CRAP!

gt35slider Explorer

gt35slider

Posted
Posted

I agree with what u have said but my safe tune is 18psi for a turbo that should be running 20 to 26 psi. I chose a .63 as I been in .82 and was a touch laggy for my liking. In future I will change to a .82 with more boost and aim for big hp.

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

I agree with what u have said but my safe tune is 18psi for a turbo that should be running 20 to 26 psi. I chose a .63 as I been in .82 and was a touch laggy for my liking. In future I will change to a .82 with more boost and aim for big hp.

fair enough but ideally you should be running a smaller gt30 with a larger (1.06) rear housing to get the same sort of power with better response and less stress on the engine (those .63 housings arent great for cylinder scavenging and temps). it'd also come on boost much smoother than the .63 gt35, making it much easier to control wheelspin.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • oHBoy.
      2001 R34DE

      By oHBoy. · Posted

      3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...