Jump to content
SAU Community

R33 Gtr - How Much Can The Stock Turbos Make?

R33-RB26DETT
 Share

Recommended Posts

R33-RB26DETT Proficient

R33-RB26DETT

Posted
Posted

I've searched and there are a lot of varying comments, I would like to get a definitive answer if possible.

1. What is the maximum AWKW's that an R33 GTR will make with all other all supporting mods?

2. What would this translate to in terms of RWKW's?

My understanding is that you can do the following:

- Run 1.1Bar and achieve 240 AWKW's, is that right?

R33-RB26DETT Proficient

R33-RB26DETT

Posted
  • Author
Posted (edited)

283.8rwkw at 1bar.

unsure about R33's in awd though. the above figure was a bit hard to believe until i was shown proof that it was correct. minimal mods too!

Wow that's amazing! so what would that translate to at all four wheels? Like around 240awkw's?

Edited by R33-RB26DETT
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Wow that's amazing! so what would that translate to at all four wheels? Like around 240awkw's?

rwkw and awkw is the same.

A GTR is NOT fulltime 4WD 50/50 split. It does not have a centre differential etc etc.

250rwkw would be around 240-250awkw. It's fk all difference.

This is been covered many times before, and you can check the dyno results thread with about 100 results on stock turbos.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...