Jump to content
SAU Community

Recommended Posts

Yeah one of mine has metal rather than woodgrain (dunno what era/series' didn't have woodgrain, I thought they all did)...it was painted some weird brown color, I sanded it back and painted it gloss black, it's just a sheet of stainless steel that inserts into that trim piece.

The woodgrain stuff isn't too bad, if you don't like it, it's only plastic, just sand it back and paint it.

It's not something that would be optional, it'd have to be standard then on all series' then.

i assume :) , the trim in my old one may have been swapped as it was the light blue/grey trim not brown like most black c33

Not keen on the fake wood on the C33 dash. Did they do any without that?

yeah s2 were much nicer , but you could peel the wood sticker off the s1 and paint or put carbos sticker on it (whatever floats your boat)

  • 4 weeks later...
  • 1 month later...

http://www.importmonster.com.au/view?url=http://page9.auctions.yahoo.co.jp/jp/auction/k143055677&thumb=http://f2.auctions.c.yimg.jp/img329.auctions.yahoo.co.jp/users/0/0/9/2/copen32z-thumb-1310179593678500.jpg&title=Z32%20R31%20C32%20C33%20Z31%20A31%20Y31%20F31

I honestly have no idea what that is.

Judging by the bracket and the cable...it looks like a convertor for the coilpack loom....maybe S1 (R31, A31, C33) to S2 (R32, later A31/C33)

Bracket appears to bolt on over the top of the existing ignition module, this thing goes onto the same bracket, then the wiring harness joins the two.

  • 2 weeks later...

If I didn't just buy brand new SuperSparks, I wouldn't be posting this.

Awesome ignition setup, suit RB20DET

http://www.importmon...itle=A31%206G34

Simply plug into ignition module, and run leads to spark plugs.

Half the cost of brand new coilpacks.

============================================================

A31 Cefiro/C33 Laurel Roll Cage (presume non-sunroof) - CHEAP

http://www.importmonster.com.au/view?url=http://page10.auctions.yahoo.co.jp/jp/auction/m91566295&thumb=http://f5.auctions.c.yimg.jp/img353.auctions.yahoo.co.jp/users/8/5/2/5/kazuyuki_jzx90-thumb-1312886779944090.jpg&title=31

Edited by Nic_A31

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...