Jump to content
SAU Community

Recommended Posts

those look nice there mate, been thinking about getting a new set of boots for the gear boot and hand break, but haven't been bothered as of yet, are they eBay special for like $20 odd plus like $5 for P/H?, if so, can you let me know how they go please

yeah they are, 20 bucks, and 9.90 postage from britania land, the leather is nice. everything fits well, even the rubber top in the gearstick boot. its made to replace the original exactly. i had to trim a little excess around the bottom of the gear boot, and the wire frame in the handbrake boot is a little to soft compared to the original, but hasnt been an issue yet (if it pops out ill add a few dabs of glue).

Mmmm car smells like leather

nice figures mate,

yeah it's sledgehammer like, on another note:

Those who are wanting to cruise down to QR as a group we are meeting at the southbound BP on the highway at 4:30am for a 4:45 leave time, This gives everyone 15 mins to grab some fuel a coffee and a feed.

Those who are wanting to cruise down to QR as a group we are meeting at the southbound BP on the highway at 4:30am for a 4:45 leave time, This gives everyone 15 mins to grab some fuel a coffee and a feed.

Make that 4AM just to account for slow people and a quick hello.

been thinking a little lately, i have 2x 10" thermos i want to install into the skyrine, and i was wondering if this would be benificial or would it be better to just get like say a single 16" thermo

Thermo fans are only benificial if you have a shroud for them. There are some shrouds if my memory serves me correct on ebay that suit the standard rad. Control wise, I'm not a hugh fan of the thermo control units that use the probe in the top hose, you would be better off using a thermo switch sender mounted in a bit of stainless pipe in the top hose. If you have an aftermarket computer you can use it to trigger a relay.

happy laps were double as happy!!

track started getting wet again after we had breaky and they asked us to go out again and dry the track off for them (V8 Experience guys).

sry for leaving yas behind, i was in a hurry. Clint you and old mate (forgot his name already) make it thru ok?? i got to the christening about 3 mins late :P close enough for me :thumbsup:

sry for leaving yas behind, i was in a hurry. Clint you and old mate (forgot his name already) make it thru ok?? i got to the christening about 3 mins late :P close enough for me :thumbsup:

Yeah I just took Joe up to Beams road and pointed him in the direction of the Highway. I saw ralph going back the other way what was that about?

Guys it was good to see you at Double Epic Super-Happy laps!:action-smiley-069:

Thanks for having us, I will finally after 5 years be filling out my membership form and getting that sorted Monday.

haha old mate!

ended up getting home and goin back to bed for 3 hours, 4am is far too early to be getting up..

had a good day though, would have been better if clint didnt steal my ride in Noel's 33!

BTW mate, didnt happen to run into any P plater Lancers on the way home did you ;)???

Edited by GTR_JOEY

haha old mate!

ended up getting home and goin back to bed for 3 hours, 4am is far too early to be getting up..

had a good day though, would have been better if clint didnt steal my ride in Noel's 33!

BTW mate, didnt happen to run into any P plater Lancers on the way home did you ;)???

Funny you should mention P plater lancers, there was one acting the fool on the way home in the wet.

I stole that seat fair and square, I have been eyeing off a ride in the wheelchair since it was unveiled.

You'll just have to come up again when it's at lakeside then he can take ya for a real lap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
    • Probably. I take it that they are also mentioned to be for R34 Skyline? For example.... RDA has that part as RDA7957. I have the dimpled and slotted version of that on my car https://www.ebay.com.au/itm/285518478694?srsltid=AfmBOopKxMuAFpsxZJdB1cam4D5RAj1f9yJyOttPZLAwXVNCOiwlhrIy This is DBA's top one piece equivalent https://www.ebay.com.au/itm/364246686631?srsltid=AfmBOorbb0XHQgqTvZLgQPhg70nqJtGvdojKnugum3O2LFSr2h-obp8D  
    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
×
×
  • Create New...