Jump to content
SAU Community

Recommended Posts

Hey everybody, does anyone know the measurements to a stock radiator in a R34 GTT. I'm looking at upgrading to a PWR product, If anyone has already done this what were the benefits you saw, how long did it take and how much did it cost.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/357537-from-stock-radiator-to-pwr/
Share on other sites

Two bolts for shroud, two bolts for radiator top supports... bottom hose, flush coolant, remove top hose, remove radiator and replace.

Took me about 20 minutes to remove the old one and replace. Looks fat and will give you so much better cooling potential. Very worthwhile upgrade in my opinion.... next is silicone hoses and better clamps.

Also the radiator has nice strong alloy hose outlets, as opposed to crappy plastic ones that break in your hoses.

Thanks mate spoke to a guy called jamie at Natrad radiators in midvale said its top of the line in radiators, but also mentioned that if your at the lights it can creep up over half way on the thermostat, but as soon as you get going again it flys back down, do you think this is a huge problem or is it cause that the radiator is made out of aluminium. Also I'm gettin a Garrett GT30 turbo upgrade, bigger injectors and a airflow meter installed soon do you think that having the radiator put in will help keep everything cooler or be the same with a stock.

It will probably be the same as stock or better. Ebay aluminum radiators work a treat :) no problems with them so for a while.

Depends what you're using them for.

I had an ebay ally radiator and it used to heatsoak something horrid after half an hour on the hwy and temps would just steadily increase. It also couldn't handle a decent burnout on a 40deg day, would spit coolant everywhere.

Turfed it in favour of a stock 32GTR radiator and the difference was huge. Temps well under control, a good 2.5min burnout on a 40deg day would see no more than 105deg.

Also a FYI, temps WILL increase when stationary UNTIL hot enough to engage the clutch on the engine fan. If it gets TOO hot, the A/C fan will kick in.

Another FYI, you won't notice the needle on your factory temp gauge move until the temps are over 100deg.

  • 10 months later...

Nah not yet mate was gonna be the last of my engine mods, previous mods were tomei typeB camshafts, bigger rear housing on turbo, on top of other previous mods now running 324HP so pretty decent for everday car will post up when done and if increase in hp or better performance overall. Spoke to a guy a Natrad radiators a few times, so have a few other people on this site says there the shit, so i will have it done eventually.

Are you having overheating problems at the moment? Do you have an oil cooler?

I am running the stock radiator and clutch fan with 400rwhp and no overheating issues.. Got a bit hot on the AHG pan with then it was understandable considering the ambient temps.

An oil cooler would be of a lot greater assistance than going for a replacement radiator - unless it is faulty.

Are you having overheating problems at the moment? Do you have an oil cooler?

I am running the stock radiator and clutch fan with 400rwhp and no overheating issues.. Got a bit hot on the AHG pan with then it was understandable considering the ambient temps.

An oil cooler would be of a lot greater assistance than going for a replacement radiator - unless it is faulty.

Good point on the oil cooler. I'm not sure about the OP but my radiator is visually rusted inside so I'll conduct another flush and replacement. I'm also considering a cross-flow radiator. Anyone have any experience with the PWR crossflow (or any other company)?

  • 2 weeks later...

In all honesty mate spend your money on something else for your car.

My 32 is running a standard rad and after 5-6 laps of beating the piss out of it around barbs it is still only around about 115 deg.

IMO dont replace it unless it's broken

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...