Jump to content
SAU Community

Recommended Posts

  • Replies 804
  • Created
  • Last Reply

Top Posters In This Topic

GTR or GTSt?

as said both plus all the s series stuff. also have f-a-s-t if you want it (older version. does upto early r34 (inc gtr) stuff just not the later 34)

This is my new ride as of last Tuesday =]

looking good.

He gave me all engines from ca to 26.

Ahh the R32 All Engines manual :P

I've got a 32 GTR workshop manual too which helps with a lot of the body/chassis/electrical stuff, it's GTR specific but GTSt is close enough in most aspects.

Ahh the R32 All Engines manual :P

I've got a 32 GTR workshop manual too which helps with a lot of the body/chassis/electrical stuff, it's GTR specific but GTSt is close enough in most aspects.

I am trying to find a gtst wiring version. I have a early 32 but want to fit a late model 260 speedo

If it isn't the same as that gtr cluster page I sent you ages ago, you could just swap the speed sender over from the old one onto the new and fit that into the old cluster housing.

There is a writeup in the tute subforum a couple of years ago on how to do it.

I pulled the harness out of the back and checked it all out and it is slightly different, i'll check out that tutorial. I'm not really auto electrically advanced i have been known to let the smoke out of the wires. Driveline on the other hand i know

any more done bubba?

Not really, have gone pretty much as far as I can until I get my plenum back and get my bends for the dump pipe.

What I will be doing tomorrow is going to see Steve May to get some clutch master cyl. nuts and an R33 GTSt power steering resevoir. The standard resevoir doesn't quite fit around the Neo turbos elbow so will get a 33 unit as they are much shorter. That means I can't run the extra loop on the p/s system without Tee-ing into the single return so I'm going to order one of those bypass fittings from JJR.

So yeah tomorrow, collect a couple of bits, bolt clutch MC down then I'll probably chuck the front up on stands and get a mate to help me bleed the clutch and brakes.

Anyone a machinist in here? need to get a couple of fittings made up.. my nice -10 breather fittings don't fit under the bonnet :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...