Jump to content
SAU Community

R32 Headlamp Adjusters

jiffo

By jiffo,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

jiffo Mentor

jiffo

Posted
Posted

If you're about to fit new headlight bulbs, better check your adjusters are working.

Here's the back view of the right headlamp, the low beam adjusters are circled blue, high beam circled red.

The low beam adjusters are simply a threaded rod which tilts the reflector and some WD40 will help them to move nicely.

rightheadlight.jpg

The high beam adjusters have a small gearbox to tilt the reflector.

highbeamadjusters.jpg

Inside the gearbox is a bevel gear driving a gear on the end of the threaded rod, which again tilts the reflector.

gear.jpg

As you can see the drive gear splits on its shaft and so no more adjustment.

brokengear.jpg

Link to comment
https://www.sau.com.au/forums/topic/358570-r32-headlamp-adjusters/
Share on other sites
ausdrift Experienced

ausdrift

Posted
Posted

Thanks. I have a R33 and need to do shaken inspection next month (im in tokyo) and this is something many cars fail from. Although i cant adjust them meself (need very specific setting that only a machine can set) its interesting to finally know how its done

  • 7 months later...
Dougz32 Rookie

Dougz32

Posted
Posted

I would like to adjust mine as my passenger side low beam is directed straight at the ground.

I'm having trouble removing the headlight assembly. Could you help me out? Or is it possible to do it while the headlight is still in the car?

iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted

From memory, you have to take the indicators out, then looking at the headlights from where the indicator would have been there is a nut that has to be taken off.

Then on the back of the headlight there is two nuts that have to be taken off. I have circled them in green on the picture :)

zla9x.jpg

  • 4 weeks later...
HYBR3D Collaborator

HYBR3D

Posted
Posted

I would like to adjust mine as my passenger side low beam is directed straight at the ground.

I'm having trouble removing the headlight assembly. Could you help me out? Or is it possible to do it while the headlight is still in the car?

HYBR3D Collaborator

HYBR3D

Posted
Posted

I would like to adjust mine as my passenger side low beam is directed straight at the ground.

I'm having trouble removing the headlight assembly. Could you help me out? Or is it possible to do it while the headlight is still in the car?

If you need to adjust them ou need to do it on the car or how can you see where it's pointing? I just did Myne last week because my lows were pointing at the ground. Was piss easy. All you need is either a ratchet spanner or a small socket set size 8 I think. squeeze it in there and turn away. It dosnt take much to adjust alot of direction. Only thing is you need to get that machine to get the levels really accurate I just did it on a wall in the dark.

  • 4 months later...
Dougz32 Rookie

Dougz32

Posted
Posted

If you need to adjust them ou need to do it on the car or how can you see where it's pointing? I just did Myne last week because my lows were pointing at the ground. Was piss easy. All you need is either a ratchet spanner or a small socket set size 8 I think. squeeze it in there and turn away. It dosnt take much to adjust alot of direction. Only thing is you need to get that machine to get the levels really accurate I just did it on a wall in the dark.

Thanks. You're right. Was piss easy haha. Thanks for the help

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R33 GTST Sh*tbox to Polished T*rd

      By Duncan · Posted

      Nice, thanks for sharing your progress....that's a pretty long list you are putting into it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Decided to upgrade my pressurised plastic coolant expansion tank for a fancy pants alloy version The OEM versions can get brittle, even the new plastic one I got when I first got the car is a starting to show signs of "stress" I wasn't cheap, but it is basically unbreakable
    • pacman_1219
      RB25DET Neo Rebuild

      By pacman_1219 · Posted

      Morning all, I have an RB25DET Neo that's in need of a rebuild. Will need new pistons etc due to detonation damage. Would anyone be able to recommend a shop in Southeast Queensland who I could bring my long motor to for a rebuild? Just want someone who knows RBs and whos built a bunch of them before. TLDR - recommended engine shops for RB rebuild.
    • Yeetus
      R33 GTST Sh*tbox to Polished T*rd

      By Yeetus · Posted

      Gday Thought it was about time I started a build thread! As expected this project has snowballed into a huge financial liability, but unless you’re strong willed and responsible, it’s not a surprise. Background -  My first turbo car was an R32 GTS-4, got my full license and then totalled my Au Falcon a week later, so while trying to sell my RMZ450 dirtbike to buy another car a bloke offered to swap the R32 which at the time I felt like I was ripped off but looking back and seeing prices of those now ($40kish) it was a good deal, I didn’t know enough about these cars to appreciate what I had so sold it before the RB20 blew up. Between here and there, out of 12 cars I’ve owned the note worthy ones are a V8 Lexus SC400 (soarer), a couple of XR6 Turbos and my beloved S15 which I had for about 3 years, picked it up for $12500, repairable write off but she was fine, gun metal grey/pewter and bone stock/unmolested until I got my hands on it. Ended up spending about the value of the car and 280kw, 2 demerit points by the time I got defected and sold it for $14500 (also $40kish in today’s market, rip) Fast forward to the present day, I’m in a much better position financially and daily an MQ Triton (great cars, pipe down Ranger Bois), I cruised marketplace and car sales for a few months looking for another R32, the best deal I could find was an absolute rust bucket half finished project for $12000, until this R33 popped up in Port Macquarie for $18k - unregistered and barely running but decent shape, kept an eye on it for a few weeks and the price steadily dropped, $16k then $15k then $14k, that was the point where I was like shit someone’s gonna snatch this up! It was owned by a young bloke who had big plans but him and his missus just had a baby so smartest move financially for them but big gain for me. So 2 days later I’m towing a car trailer to pick this thing up. Roughly 2 weeks and $3500 later I’m cruising around Newcastle in my beat up R33 all smiles and dose noises! It only needed some basic shit to get it going, coil packs and air flow meter, electrical stuff and all fluids changed, 158k kms and running pretty good, nice smooth engine after oil and coolant flush - when I say coolant I mean it had been filled up with tap water, every gallery and heater element was filled with rust, 8-9 flushes later and still had brown liquid coming out but she’ll be right. The car was painted R34 Bayside Blue at some point but whether it was a cheap job or just not looked after is anyone’s guess, clear coat flaking like sausage roll.  Was rethinking my choices and contemplating life, had it up for sale for $22k - still cheaper than any registered R33 but got little interest, next minute I had an opportunity at work - 6 months overseas for good money, so that was a no brainer, fast forward again and here we are with a 50% finished project. Current Mods - 200ish KW according to butt dyno Was tuned with Apexi PowerFC EBC (old school Greddy Profec)  Stock turbo (more shaft play than a Tinder date gone right) 3inch turbo back Varex muffler  Aftermarket injectors of mystery size, Power FC showed 36% duty cycle at full boost so not behd good size Someone had good intentions but stuck with the stock R33 MAF so we had misfires at 6000rpm due to the MAF hitting 5.2V So far I’ve redone the entire interior with carpet form Car Mats Direct, new Seats and steering wheel from Autotechnica, also sound system by Autobarn (mainly Kicker) Also MCA pro comfort coil overs - Hands down best purchase yet, worlds of improvement over the tired 30yrold shocks Goals - 450kw/600hp on flex tune New paint job - Midnight Purple 2 Engine is at the shop getting rebuilt with forged rods a pistons, new valves and springs, ATI Harmonic balancer, Aeroflow 7.5L sump, rear head drain and oil restrictors as per oil control thread* and cam covers modded for larger breathers, other stuff I can’t recall of the top of my head Parts purchased and to be installed once the engine is done -  Engine loom from Wiring Specialties including these options: Haltech Nexus S3 R35 Coil pack conversion  PRP Dual Trigger kit Fan controller  Other Parts -  262 Kelford Cams Turbo - Hypergear ATR43SS3-ProS with T51R mod (whistly boi) 6 boost manifold (high mount) 50mm Turbosmart Pro gate (plumbed back for legal reasons) HKS Super Turbo Exhaust with High Flow Cat Custom 3.5inch dump and front pipe 1500cc Bosch injectors  Fuel Pump walbro 525 Haltech MAP and IAT sensors Haltech Flex Sensor Fenix Radiator with dual thermo fans LS1 Alternator Kit Oil Filter Relocation from EFI solutions and Cooling pro oil cooler Many other things sitting in my garage waiting for that engine to come back. Progress pics to follow -  
    • GTSBoy
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By GTSBoy · Posted

      Losses have to be less with DC coupling. Provided the battery inverter has decent MPP tracking ability - which really shouldn't be a problem. It's not 2005 any more.
×
×
  • Create New...