Jump to content
SAU Community

Recommended Posts

Ok i have used fishing wire to debadge the stagea. I has tried to use grease and wax remover to get rid of the glue but still leaves the outline of the wording. What have you used in the past thatwill get rid of the glue and any marking from the lettering.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/
Share on other sites

You could also try Mineral Turpentine on a rag and/or a very light polish as there will be a difference in the paintwork finish now where the badges have been...

+1 thats what i did.. just polished it up and it came up perfecto

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5742633
Share on other sites

Ive done the same on mine got all the adhesive of with some metho on a rag and then clay bar, cut and polished then waxed where the badge was but you can still see where it was...... Think i need to find someone to hit it with the buffer.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5742798
Share on other sites

It should be fine, although it will most likely strip the polish from the surface leaving you with a dull patch that you'll need to repolish.

It's not different from a bit of petrol running down the side of the car when you're filling the tank - I hate it when it does that!

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743078
Share on other sites

Ok got all the glue off. Not I just have like a dirty outline of what used to be there. What would be the best grit sandpaper to remove this before I cut and polish. Would wet sanding be best

Just use a cutting compound, and keep going until you get the finish you're after. The clear coat on these is far too thin for wet sanding IMO.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743249
Share on other sites

Just use a cutting compound, and keep going until you get the finish you're after. The clear coat on these is far too thin for wet sanding IMO.

+1 on the cutting compound and i wouldn't go near it with wet & dry either.

I'd also use a light hand when using the cutting compound and just take your time.

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743266
Share on other sites

unfortunately the badge the car in the factory when the paint hasnt quite cured so leaves marks. plus the weather etc doesnt help.

mine and craigs are the same. no amount of cutting and polishing etc got the marks out of mine

Link to comment
https://www.sau.com.au/forums/topic/359557-debaging/#findComment-5743627
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
×
×
  • Create New...