Jump to content
SAU Community

Recommended Posts

Hey all I have just purchased a an r34 sedan car has a 3076r with all supporting mods (fmic, inj, afm etc)

Also has a "heavy duty" radiator.....it has standard top tanks but core looks to be about 40 mm thick (standard is around 15mm)

when driving normaly the temp sit in the middle of the of the factory gauge (my other standard r34 sits in the same place)and the aftermarket gauge which is in the top radiator hose sits about 100 but when I drive it a little bit hard ie full boost a few times up to 100km or so it heats up to about 110 120t is this normal to have quite vast temp changes with such little hard driving or am I being paranoid?

Im only worried because my old silvia had a similar set up but ac was removed and had a thick koyo radiator temps never went above 90 on a 30 degree day no matter how hard I drove it

should I look at getting

transmission cooler

oil cooler

alloy radiator ?

any imput would be apprecated thanks Ben

Link to comment
https://www.sau.com.au/forums/topic/359918-r34-3076r-running-temps/
Share on other sites

Transmission and oil cooler won't lower the water temperature...

100 seems rather high? My temp gauge sits at around 70-75 during everyday driving, doesn't make much difference what the outside temperature is. Gets maybe as high as 90 if I'm flogging it around. That's with a triple core alloy radiator though.

I've got a R33 with a 3076R and mine never gets that hot. It'll run around mid 80's to low 90's at the track on a 30+ degree day. All my cooling system is completly stock too. I would be looking at either the themostat, how far is it opening? The fan, not sure if 34's are still mechanical fans, but check your belt tension and fell how much air its blowing as the clutch on the fan may be not locking up. Biggest issue if it has a bigger rad is it using the cowling? If theres no cowling this can cause serious air flow issues and not draw enough air through the rad.

I've got a R33 with a 3076R and mine never gets that hot. It'll run around mid 80's to low 90's at the track on a 30+ degree day. All my cooling system is completly stock too. I would be looking at either the themostat, how far is it opening? The fan, not sure if 34's are still mechanical fans, but check your belt tension and fell how much air its blowing as the clutch on the fan may be not locking up. Biggest issue if it has a bigger rad is it using the cowling? If theres no cowling this can cause serious air flow issues and not draw enough air through the rad.

So should I give one of these a go? http://www.justjap.com/store/product.php?productid=16888&cat=&page=2

How do i tell if the fan is locking up I just had a look and it spins quite freely

You guys over there have stolen the good weather so no surprise something like this is coming up :)

Forget thermostats mate. Stock is fine.

What you need to do first is get the radiator out, give it a good flush and a refill with distilled water and so on. I believe you can get them flow tested too so this would be a good idea.

Also the FMIC could not really be flowing much air and blocking which will also cause issues.

If giving it a solid flush and so on does not work, then you'll need to invest in a decent radiator. By saying the one you have now looks as if it has stock header tanks, then i'd be dubious of it being aftermarket.

A decent 40-45mm ally radiator from somewhere like Race Radiators (a melb mob, just as an example)... Will almost certainly fix the issues.

HOWEVER don't go for the fix immediately, best to know what is the issue first.

Transmission and oil cooler won't lower the water temperature...

100 seems rather high? My temp gauge sits at around 70-75 during everyday driving, doesn't make much difference what the outside temperature is. Gets maybe as high as 90 if I'm flogging it around. That's with a triple core alloy radiator though.

Do you have a low-temp thermostat as well?

My experience with a stock R34 and brand new thermostat is that it sits pretty solid between 88C & 90C in most situations. The R34 thermostat doesn't open until 85C and fully open by 95C from what I recall.

My 2c =

Put a new thermostat (OEM) and a factory radiator in it. Im confident this will fix the issue.

As Ash said, intercoolers can be a problem. I had an older model JJR core on a car of mine a few years back and had all world of trouble.

Do you have a low-temp thermostat as well?

My experience with a stock R34 and brand new thermostat is that it sits pretty solid between 88C & 90C in most situations. The R34 thermostat doesn't open until 85C and fully open by 95C from what I recall.

Stock Neo thermostats are 82deg

My 2c =

Put a new thermostat (OEM) and a factory radiator in it. Im confident this will fix the issue.

As Ash said, intercoolers can be a problem. I had an older model JJR core on a car of mine a few years back and had all world of trouble.

Ditto, as I've said in other threads, I had a cheapo china radiator and while it was nice and thick, it used to heatsoak horribly, tossed it in favour of a GTR radiator and had no more dramas.

Do you have a low-temp thermostat as well?

My experience with a stock R34 and brand new thermostat is that it sits pretty solid between 88C & 90C in most situations. The R34 thermostat doesn't open until 85C and fully open by 95C from what I recall.

It's stock as far as I know, I haven't put in anything aftermarket. Small chance that it has an aftermarket one in it from Japan but I wouldn't know for sure.

Your thermostat could be stuck/blocked, replace this first (it's the cheapest and easiest)

check-temps again

Replace the radiator with something that slides right in.

While you are at it replace all the water hoses. yep..ALL of them.

Have a beer and never worry again about over heating.

Hottest I've seen my car is 88°C when driving in heavy traffic in 40° days(R33) but R34 will get a few degrees warmer.

Anything over 95° is too hot, ever.

Yeh 95 isn't that bad. With coolant and a properly pressurized system, you're no where near boiling point. I've seen my water temps hit 110 during a track day, have seen full on race cars reach as high as 160 degrees without damaging anything.

Anything over 95° is too hot, ever.

No, it's not.

Maybe EVER was too strong a word. If you get above 95° simply by doing a few 0 -100 sprints then you have a problem and need to address it.

The R34 was designed as a slightly higher temp RB25 than the R32/R33 for efficiency.

Increasing the coolant temp ~10°C roughly doubles the pitting and deposit formation and therefore results in faster wear on water pump impellers, heater cores, dissimilar metals, etc. People may think high temps haven't damaged anything simply because nothing has broken immediately, but parts in the cooling system and gaskets get damaged.

Edited by simpletool

Anything over 95° is too hot, ever.

Maybe EVER was too strong a word. If you get above 95° simply by doing a few 0 -100 sprints then you have a problem and need to address it.

The R34 was designed as a slightly higher temp RB25 than the R32/R33 for efficiency.

Increasing the coolant temp ~10°C roughly doubles the pitting and deposit formation and therefore results in faster wear on water pump impellers, heater cores, dissimilar metals, etc. People may think high temps haven't damaged anything simply because nothing has broken immediately, but parts in the cooling system and gaskets get damaged.

Isn't it every 10 degrees over the maximum coolant operating temperature halves the engine life expectancy? Not sure what that maximum temperature is on an R34, but it would surely be much higher than standard water boiling point.

Anything over 95° is too hot, ever.

Maybe EVER was too strong a word. If you get above 95° simply by doing a few 0 -100 sprints then you have a problem and need to address it.

The R34 was designed as a slightly higher temp RB25 than the R32/R33 for efficiency.

Increasing the coolant temp ~10°C roughly doubles the pitting and deposit formation and therefore results in faster wear on water pump impellers, heater cores, dissimilar metals, etc. People may think high temps haven't damaged anything simply because nothing has broken immediately, but parts in the cooling system and gaskets get damaged.

Do you have evidence to back up your scaremongering?

I agree that if you're reaching 95deg after a couple of hard jaunts up to 100kmh there is an issue that likely needs to be addressed.

Telling people that reaching 95deg is OMG GOING TO REDUCE THE LIFE OF EVERYTHING THE COOLANT TOUCHES, is scaremongering.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...