Jump to content
SAU Community

Recommended Posts

Well as the title states my catchcan vent blocked and the 32 started spewing white smoke... I get about 2 psi of boost and I'm wondering if the pressure has blown out my turbo seal...? If anyone could shed some light on this for me so I know where I'm at I'd be very appreciative.

Link to comment
https://www.sau.com.au/forums/topic/359985-blocked-catchcan-vent-killed-my-32/
Share on other sites

???

How could a blocked catch can put pressure on the turbo's bearings?

The white smoke would be oil spewing back into the intake from the catch can... There's no way the bearings would "blow" from this...

???

How could a blocked catch can put pressure on the turbo's bearings?

The white smoke would be oil spewing back into the intake from the catch can... There's no way the bearings would "blow" from this...

Not entirely true.

Increased pressure in the crankcase will prevent oil returning from the turbo. However it is more likely you will see the smoke as a result of it in your intake first.

The can wasn't plumbed back into the intake... also I noticed, under the bonnet, oil dripping on my plastic sump guard from the turbz area... I hav'nt looked at anything yet but was also wondering if this would've done something to the engine? only drove a few hundred meters when I noticed the smoke

Have seen first hand what excessive crank case pressure can do to turbos, which is what you would have had with blocked breathers...as was mentioned above, oil in the turbo cant return to the sump and builds in the turbo core, it then pushes past the exhaust seal, in my case, the exhaust seal was shagged or had moved according to turbo builder and I had sh1t loads of white smoke, like you...

have you fixed the catch can?

take the dump pipe off the turbo and see if there is an evident oil leak from the seal. and same on the front, if you cant see any oil there, put the intake back onto the front and start the car to see if smoke starts pouring from the turbo exhaust, if it does turn the car off and see if you can see oil in the exhaust of the turbo.

let us know how you go

Yep, exhaust wheel will look 'wet' and you probably wont see this until the turbos off but oil will be weeping down the bottom of the front side of the exhaust housing, let us know how you go...mine wasn't caused by blocked breathers but excessive piston to bore clearance...same result - excessive crankcase pressure and a turbo that couldn't drain..

Edited by NSNPWR
  • 3 months later...

Well... new turbo ( already had ) and all exhaust and ceramic coating etc and still getting slight smoke out back from oil... maybe valve seals blown out..?? any help would be appreciated, dying here... pinch.gif

yeah I had some smoke after installing new turbo and ceramic coated dump etc went away after a few heat cycles, I assumed it was just burning off shit from new turbo and new coatings..

another time needed to put a restrictor in the oil feed of the turbo, because with Jun pump was pumping too much oil and pushing past the seal, hence blowing white smoke..

hopefully just one of those reasons for you :thumbsup:

???

How could a blocked catch can put pressure on the turbo's bearings?

The white smoke would be oil spewing back into the intake from the catch can... There's no way the bearings would "blow" from this...

If you seal the crank case gases in it will pressurise and can burn lots of oil, I've seen it happen before. Don't see how it would do anything to the turbo though.

I found oil in the mouth of the compressor side when I was putting a boost controller in and had to remove stuff to get to the actuator... hoping its from it sitting around for so long..?? stretching maybe but dont want to think I have to pull it all off again... also I have taken it for a couple runs before that and it was showing white at the end of the runs and a hint of blue due to not being mapped..

Edited by partyboy73

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...