Jump to content
SAU Community

Recommended Posts

2 weeks ago i purchased my 350z anniversary wheels , although they were just a little to plain for me in the standard alloy colour . so today i thought id pull out the spray gun and give them a more stealthy aggressive look. the paint i used was the factory black r34 GV1 from memory .much to my suprise they came out better then i expected , totally give the car a different look.

for anybody at home looking to do something similar, the process was pretty simple .

1. rough up existing paint with 400 gritt

2. clean with thinners

3. spray a dust coat with the base paint.followed by 3 firm coats

4.2-3 coats of clear

5. maybe even a bit of a cut and polish depending how fussy you are

overall the end result was worth the time , took about 1 hr per wheel , off and back on again. ill throw a final pick up tomorrow , bit too dark by the time i got inside :P

cheers , and comments or questions hit me up

post-32277-0-17504400-1302597436_thumb.jpg

post-32277-0-78745000-1302597656_thumb.jpg

post-32277-0-26764700-1302597665_thumb.jpg

post-32277-0-16068600-1302597676_thumb.jpg

post-32277-0-32547600-1302597777_thumb.jpg

Edited by sky017
Link to comment
https://www.sau.com.au/forums/topic/360681-bit-of-diy-painting-today/
Share on other sites

Arthur T3 - it was a pretty sunny day yesteday when i sprayed them, being acrylic it dries pretty quick too. but what i did was after id spray the clear , i gave it 15 . then rolled it back to the car , carefully put it back on . put the bolts on carefully , pretty easy considering they are a pretty wide hole . then just left them over night to dry completely . saves a bit of time so i can get the next wheel, off to prep. i was keen to get them done before the sun went down :P cheers

aahh of course, it was sunny..

i live in melbourne, we dont really get that here .

Ive been painting in the shed with the heater goin and still having trouble drying, ive resorted to doin a coat a day during the week and assemmbling the next weekend :(

aahh of course, it was sunny..

i live in melbourne, we dont really get that here .

Ive been painting in the shed with the heater goin and still having trouble drying, ive resorted to doin a coat a day during the week and assemmbling the next weekend :(

hehe poor you by the sounds of it. definitly hate drying process, i try to be a perfectionist at times , but damn sometimes i just want it done and back on the car, i sprayed my rear bar on a sunny day ,then bang raining! heres me out in the garage still spraying lol. only crap thing is it goes milky in the cold , never the less all goes away when you cut it bck :P

thanks for the positives guys , much appreciated

i do a few colour coats and a couple of clear, but havent cut it, could be why my finish isnt as good,what do u use?

Think i have a bottle of mequiers fine cut would that do it?

i must say it requires a fair bit of work in regards to cutting to get that high gloss finish . usually rub back from 1500 - 2000, then use a cutting compound. iv used this septone stuff i purchased from the car paint place, followed by a polish compound ,then some other detailing polish. all depends what your doing , but thats my process for body work , seams to work for me. by the way in saying that , its a must you use a power dril or a variable speed grinder with buffing wheel / foam pad attatched to really get that gloss to shine , using some cheap buffing wheel from kmart wont be sufficient enough.

<--- see my profile pic

did this on the old r33 years ago.

same technique, wet sand, but i also used some putty to smooth out the gutter rash etc so took me a full day with all the waiting and drying.

these wheels do look nice though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would be very confident that they are the same parts (the 2 different SKUs). It seems very clear that you can drop the cam in the 2-way opening, or in the other opening. If you arrange it in the other opening in the same way that you see any other 1-way diff, ie, with the flat of the cam up against the 1° side of the opening, then it would work as a 1-way. It can only spread the ramps when driving forwards - cannot spread the ramps on overrun. It would then appear obvious that if you put the cam into the opening "backwards", that you would get the angled flats of the cam working onto the "points" of the 1° side of the opening, which would give you ramp spread in both loading directions. I do wonder if the forward direction of the 1.5-way config is equivalent to the forward direction of the 2-way, seeing as the cams are flipped and the angled surfaces on those would need to be the same on each side - AND - clearly when installed in either the 2-way or 1-1ay configuration they are not intended to work exactly the same (the ramp angles on the 2-way are 10° different between forward and backward, and the ramp doesn't exist in the 1-way config). 'twere me, I think I would rather actually have a set of rings that offered the 2-way with two different sets of ramp angles, say the 55/45 of the existing design and maybe a 45/37.5 combo for a less aggressive effect), AND another set of rings with a dedicated 1.5-way opening and a dedicated 1-way opening. The 1.5-way opening would actually have the steeper angle on the overdrive side that causes it to be less pushy than the forward drive angle, like you see in many other diffs. But really - if this Nismo thing is thought out properly and all those surfaces work on each other the way that they need to, who am I to argue?
    • I would be very confident that they are the same parts (the 2 different SKUs). It seems very clear that you can drop the cam in the 2-way opening, or in the other opening. If you arrange it in the other opening in the same way that you see any other 1-way diff, ie, with the flat of the cam up against the 1° side of the opening, then it would work as a 1-way. It can only spread the ramps when driving forwards - cannot spread the ramps on overrun. It would then appear obvious that if you put the cam into the opening "backwards", that you would get the angled flats of the cam working onto the "points" of the 1° side of the opening, which would give you ramp spread in both loading directions. I do wonder if the forward direction of the 1.5-way config is equivalent to the forward direction of the 2-way, seeing as the cams are flipped and the angled surfaces on those would need to be the same on each side - AND - clearly when installed in either the 2-way or 1-1ay configuration they are not intended to work exactly the same (the ramp angles on the 2-way are 10° different between forward and backward, and the ramp doesn't exist in the 1-way config). 'twere me, I think I would rather actually have a set of rings that offered the 2-way with two different sets of ramp angles, say the 55/45 of the existing design and maybe a 45/37.5 combo for a less aggressive effect), AND another set of rings with a dedicated 1.5-way opening and a dedicated 1-way opening. The 1.5-way opening would actually have the steeper angle on the overdrive side that causes it to be less pushy than the forward drive angle, like you see in many other diffs. But really - if this Nismo thing is thought out properly and all those surfaces work on each other the way that they need to, who am I to argue?
    • Yuh, but that one is NLA. There might be an equivalent, but I haven't looked.
    • If you hadn't bought a stand alone one already, nismo make a bolt on adjustable FPR https://www.efisolutions.com.au/nismo-fuel-pressure-regulator-sr-rb-s13-180sx-r32
    • I know and understand they are principally the same. They both cause lock under decel, but the 1.5 nomenclature implies "half" or less locking force, or it allows for more slip or a speed differential between both wheels. Right now the driving manners with the 2 way is pretty rough on transient to full off throttle in the backroads. In other words letting off the throttle too rough is not forgiving, great for drifting, tougher for controlled grip driving.      Yeah, I have watched that video a couple times, I am more so just looking for the confirmation that both part numbers offer the same ramp architecture and are just different settings from the factory.     38420-RSS15-B5  38420-RSS20-B5
×
×
  • Create New...