Jump to content
SAU Community

Recommended Posts

when i put my foot flat down and go for it i get a weird noise from the back left like a tire rubbing noise , or simaler to it yet it isnt a tyre as im running my stock wheels and suspension still

its only under power that i hear it , if i accelerate like a nana or normal it doesnt happen

noise is louder when i have people in the car and only when under power , not cruising or nana accelerating ?

???

duno..

for a few of us..scott Craig and myself, when we put the car under heavy load theres a Vibration through the driveline.

mine sort of went away when i serviced the Transmission and transfer case, and a little more when I changed the oil in the diff's.

but its still there a little.

I noticed it really on became noticable when I lowered my car, so maybe its the same thing as you say when people sit in the car.

maybe havnt taken time to notice could this be my attesa pump by any chance

When you put your foot down, odds are pretty good that the car will transfer torque to the fronts so ATTESSA seems logical.

Have you changed the fluid in it yet?

When you put your foot down, odds are pretty good that the car will transfer torque to the fronts so ATTESSA seems logical.

Have you changed the fluid in it yet?

no i might look into that as i had the car imported so am first new zealand owner , when it got serviced , complianced etc i thought they would taken car of all that but ye its only when car is working like actually working

got my 10000 k service coming up so will get that all looked at aswell with the weird sounds like cam belt noice from front when i turne car of so might be one of the belts ( not cam chain i know )

is the transfer case in back rear area or close to as ye its well cant explain but it only comes in after im through like 2 gear and power is down

Edited by Sidius

the transfer case is at the back of the gearbox.

sounds like an exhaust leak tho. youre probably not building up enough boost in first gear, but 2nd and above you are, and its pushing out a hole.

the transfer case is at the back of the gearbox.

sounds like an exhaust leak tho. youre probably not building up enough boost in first gear, but 2nd and above you are, and its pushing out a hole.

definatly not an exhaust leak i at least know that its rear right

my exhaust is rear left

ohh sorry i misunderstood as you said rear left in your first post. right where the exhaust is.

do you know which side is which? lol

my mistake and no its quite load and vibrates a little sounds like a tyre rub on speed yet it isnt ???

i think you mean attesa dude lol

there is a loop to run the pump on M35s

yeh? its also Ian, but you dont see me complaining LOL

so with servicing the attesa transfer case and or pump

any pointers , as in any mods that can be done while im there

nah. just use a 100% synthetic AT Fluid.

theres some how too's on the M35.info forum if IAIN helps you with the link

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...