Jump to content
SAU Community

Recommended Posts

Hi All.

Just looking for an M35 air intake snorkel, as my car never came with one (it's currently being complied and should be ready next week).

I'm aware the V35 is the same but aren't having too much luck finding one (for a reasonable price in SA anyway).

I would prefer SA based, but welcome interstate help. :cheers:

Link to comment
https://www.sau.com.au/forums/topic/361583-wtb-m35-intake-snorkel/
Share on other sites

Do you mean the "Power Duct" on the top of the airbox? I think only G35s and/or V35s came with those, and you may as well make your own.

nah, not the power duct, the first section which catches the cold air through the bonnet/grille.

Brad - compliance is fine, it's the fact that I'll be sucking hot air continually without this section.

nah, not the power duct, the first section which catches the cold air through the bonnet/grille.

Brad - compliance is fine, it's the fact that I'll be sucking hot air continually without this section.

Pretty sure Ian's got a spare.....but his OS tell next week!

Pretty sure Ian's got a spare.....but his OS tell next week!

:thanks:

Yeah, I followed his link to the other 'mysterious' site but didn't pursue it any further when I read "Everything in front of the engine is damaged, so don't ask for those parts".

I'll head back over to the other site and let Iain :ph34r: know I'm looking for one.

Below is a pic of the actual part required....

M35intakesnorkel.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...