Jump to content
SAU Community

Recommended Posts

Currently in Sydney

2G firm....

original aerotech buckets

VN group A (NSV build with build plate)

original CSA alloys...

identical interor to orginal and exterior with all badges...

(seats alone would be worth at least 4g........)

143000km

chris

0478058818

email: [email protected]

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

more pics to come when i find them....

wont let me upload i will have to alter the type and then upload.....

i know.... i had some on face book but the pics have vannished due to my Facebook account being hacked and/ or it being monitored by the feds / acers/ asio/ asssic / dsto intelligence surveilance and recon etc... will post them up when i can find them.....

the seats and rims are phat.... best buckets i have ever sat in from a factory spec car..... they are awesome....

has stiff suspension too...... damn stiff,..... handles like it is on rails however it could do with some expensive rubber....

  • 2 weeks later...

no do not have any dyno sheets... it is prob not more than 120 kw at the wheels with the current set up... if need be i can get you a VP commodore motor with a twin turbo sr20 set up with dump pipes and cooler and piping aswell as braided lines that has been pro built for about 1600 more... that should be good for a safe 200kw at the wheels.... not bad for 3500 approx all up....

chris 0478058818

But dyno sheets help us tell how the car drives! It's an important part of selling a car, how else are we going to be able to tell how it behaves on the road?

Hi, can the stock R33 cat be included in this sale?

probably the only thing you would ever get related to gina -- some stocky exhaust part - (catconverter) and if you did happen to get sum, no doubt you would pay for it too............

pics of car please?

i have lost the cable that connects my phone to my computer so hence can not load photos of the car.... as soon as i find this cable i will upload.... for some reason the photos on face book that i have of the car are not supported on this site???

But dyno sheets help us tell how the car drives! It's an important part of selling a car, how else are we going to be able to tell how it behaves on the road?

it is an unmodded stockish Group A where everything is identical to the real thing except for the transmission, motor and the steering whee (it was built by Northern SPecial Vehicles and has a build plate.....

if it had been modded and had been retuned due to having some form of engine management i would defenitely put in a dyno sheet... and if you were looking for a high hp car for either track. drift or drat (which this is not) i would agree with you that a dyno sheet is a must to determine how it behaves etc.....

However i know that you are being a smart arse product of a wank stain and put this comment in for a laugh due to the comments which started the macdoogle files hehehehehee... have a good day smart arse!!!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...