Jump to content
SAU Community

Boost Cut At ~5Psi - R34 Gtt

Everlong-S13
 Share

Recommended Posts

Everlong-S13 Community Regular

Everlong-S13

Posted
Posted

Hey guys,

A friend and I installed a Turbosmart Manual Boost Controller plus aftermarket boost gauge today on my R34 GTT Neo, and we've hit a bit of a problem and I'm not sure we've connected it right.

So far I've installed the controller between the wastegate and intercooler hoses, and I currently have the lower solenoid hose blocked off. The top solenoid hose I've keep connected.

At the moment it won't boost past approx 5 psi and with the controller wound to maximum boost it gets to 5-6psi and then (I think) the ECU chucks the sh!ts and applies a fuel cut.

Is there a problem with the way I have connected everything? Many thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/362727-boost-cut-at-~5psi-r34-gtt/
Share on other sites
Everlong-S13 Community Regular

Everlong-S13

Posted
  • Author
Posted

I've uploaded a couple of pics to show what I've done.

First pic is the MBC setup:

mbcc.jpg

Also I noticed when installing the boost gauge, that one of the hoses wasn't even connected to the following valve in the pic, forget what it's called, VSV valve or something? Anyway it was never connected and I've only just noticed since purchasing the car. I can't reconnect it without getting a new one so I just clamped the hose. Wondering if this would cause any issues. See pic:

mbc2q.jpg

paulr33 Grand Master

paulr33

Posted
Posted

are you sure the guage is in PSI?

it might be mmhg or hg or kgcm2

from memory the stock ER34 has a manifold boost sensor and it trips out around 12psi

it definetly would trip out at 5/6psi as the stock boost on ER34 would be around 10psi (give or take)

Everlong-S13 Community Regular

Everlong-S13

Posted
  • Author
Posted

The stock gauge is in Kgcm2 and my aftermarket one is psi.

I'm now pretty certain the aftermarket gauge isn't working properly. It may have something to do with broken valve highligted in picture #2 - thats in a similar area where I am feeding the vacuum tube to the aftermarket gauge. I think I may need a new one of those valves.

The boost controller does work now though. I got the solenoid hoses mixed up - need to block the top one and remove the bottom completely. I can set the boost using the stock gauge which isn't entirely accurate however it's set at around 0.75 kgcm2 which is not too high.

Randon_I_Am Veteran

Randon_I_Am

Posted
Posted

I also snapped the plastic bit off that valve. It just runs under the crossover pipe to the carbon canister. I beleive that the solenoid flushed out the carbon canister of something... Just block it off so there's no vac leaks :)

mature gent Collaborator

mature gent

Posted
Posted

Hey guys,

A friend and I installed a Turbosmart Manual Boost Controller plus aftermarket boost gauge today on my R34 GTT Neo, and we've hit a bit of a problem and I'm not sure we've connected it right.

So far I've installed the controller between the wastegate and intercooler hoses, and I currently have the lower solenoid hose blocked off. The top solenoid hose I've keep connected.

At the moment it won't boost past approx 5 psi and with the controller wound to maximum boost it gets to 5-6psi and then (I think) the ECU chucks the sh!ts and applies a fuel cut.

Is there a problem with the way I have connected everything? Many thanks in advance.

bubba Grand Master

bubba

Posted
Posted

are you sure the guage is in PSI?

it might be mmhg or hg or kgcm2

from memory the stock ER34 has a manifold boost sensor and it trips out around 12psi

it definetly would trip out at 5/6psi as the stock boost on ER34 would be around 10psi (give or take)

Are you sure? because looking at the factory maps they run the same sort of TP Load limit (afm cut) as the earlier models but the values seem to have a little more meat in them.

paulr33 Grand Master

paulr33

Posted
Posted

yeah it would have AFM cut and boost map sensor cut

but it wouldnt cut at 5 or 6psi, that would be silly

the std actuator would be 7psi at a stab in the dark

anyone with stock ER34 can confirm stock ER34 boost ?

Hanaldo Grand Master

Hanaldo

Posted
Posted

yeah it would have AFM cut and boost map sensor cut

but it wouldnt cut at 5 or 6psi, that would be silly

the std actuator would be 7psi at a stab in the dark

anyone with stock ER34 can confirm stock ER34 boost ?

7psi full boost.

simpletool Mentor

simpletool

Posted
Posted

ER34 isn't 7psi. The R34 runs more boost than an R33 which runs 7.5psi and the stock tables don't run into R&R until at least 9psi. If the stock gauge is reading 0.75 kg/cm^2 then that is a touch over 10psi. This is likely the start of R&R - which from what I read is more aggressive than the R33 R&R.

You may also like to note that the stock gauge is mainly inaccurate in that it tends to read LOWER at higher boost than reality. ie. as boost rises it under reports so 0.75kg/cm^2 can be approaching to 1.0kg/cm^2 (14psi)!

You could check the stock pressure by removing the bleed valve and testing again (also confirms you have removed the 2-step boost properly). The compare to readings after reinstalling the bleed valve. Compare and contrast.

To recap - your aftermarket gauge is reading wrong almost certainly.

You are probably running 10+psi. R34 doesn't like too much extra boost - get Nistune.

Everlong-S13 Community Regular

Everlong-S13

Posted
  • Author
Posted (edited)

Thanks for the help again guys.

So it seems my boost controller setup is working fine and I have bypassed the 2 stage solenoid OK. The issue is just with my boost gauge setup.

Can anyone tell me from the picture I supplied in my first post, that where I have tapped the vacuum lines for the aftermarket gauge in is correct, and if the broken hose from the valve nearby would cause the incorrect reading on the said gauge? I'm going to have a crack and solving this tonight.

Also out of interest, when not on boost the aftermarket gauge reads quite low, towards -20 and I'm thinking that should be more like -10?

Edited by Everlong-S13

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      HFM BM57 has a "bad" knee point, IIRC. It's not the same thing as the later R chassis MC.
    • Duncan
      Who has a Infiniti Q60, Q50 (V37)?

      By Duncan · Posted

      The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • MBS206
      Who has a Infiniti Q60, Q50 (V37)?

      By MBS206 · Posted

      Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
×
×
  • Create New...