Jump to content
SAU Community

How To Install A New Dump Pipe

SLY333

By SLY333,
in Engines & Forced Induction

 Share

Recommended Posts

SLY333 Community Regular

SLY333

Posted
Posted (edited)

Hey guys ive just purchased a brand new dump pipe by Turbo Xs for my R33 Series 2 GTS-T i have put a picture below of the dump pipe, should i be paying someone to install it or is it fairly easy to put on without any dramas?? if any1 knows what is involved in putting one on lemme kno, also i have got a jasma catback exhaust so will this dump pipe be alrite even though i have a standard cat??

Cheers

3150nsi.jpg

Edited by SLY333
Link to comment
https://www.sau.com.au/forums/topic/363502-how-to-install-a-new-dump-pipe/
Share on other sites
89CAL Grand Master

89CAL

Posted
Posted

That sensor looks like it is in a bastard of a spot!

Be very careful with the bolts in the back of the turbo, you don't want to snap them. As said spray them with bolt off or wd40 etc and leave that sit for a while. If the bolt feels like it's getting tight as your undoing it, it might pay to do it back up a few turns then start undoing it again so you don't snap it.

88cameron88 Community Regular

88cameron88

Posted
Posted

undo the sensor at the plug then unscrew it from the dump once you have it off the car if you cant get to it with a spanner while the dumps still on the car.

will give more power yes! and a different noise

sinistaGTR Grand Master

sinistaGTR

Posted
Posted

those sensors can be a pain to get off, make sure you get the right size spanner onto it as they can be rather tight and the last thing you want to do is to have a spanner slip and stuff the bolt. Also get all new gaskets and personally i used a bit of gasket cement on them to make sure you get a decent seal

cannabiscorpse Mentor

cannabiscorpse

Posted
Posted

Dude, its definately job you can do yourself. I bought my first skyline (95 gtst) a few months ago and i have done everything with the exhaust myself. All my bolts including oxygen sensor werent too bad, some were pretty stiff but you get that. The guys in the post have given you good advice with the wd40, so follow that. Im not the most experienced with cars, and usually stick to just doing oil changes etc. Im lucky that i can always get my old man to help me with my cars, which comes in handy. I would definitely have a go yourself, and if your concerned just try get someone who is handy with the spanners to come round for a few beers!

I have found the skyline to be really easy to work with, and if you get stuck this site is an excellent source to get your answers.

horrace Rising Star

horrace

Posted
Posted

All pretty easy, should be able to punch it out in about 2 hours working on your back with stands, obviously put the o2 sensor in the new pipe out of the car would be borderline impossible in the car. You can get onto 5 out of 6 bolts with a small 3/8th breaker and a 13mm socket (bottom 2 from under the car) I cut down a small 13mm spanner to get to the middle passenger side bolt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      S1 rb25/s14 starting problem

      By Dose Pipe Sutututu · Posted

      When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...