Jump to content
SAU Community

Recommended Posts

LOL i would have some super problems if they were hahahahaha nah one of them is probs leaking i think but there all pritty dry and brittle ... im a bit finiky now that im learning more "2nd year shit kicker" I dont need all the individual lengths just a rough over all ... i thought most vac lines would have roughlhy the same size diamiter ? might have to do some more investigating .... bugger manufacturer ill just find some kool colours and cut it properly

Mate best bet is to pull them all off take them to a hose shop and go i need one of each :)

Yeah thats probs what ill end up doing ..... got mate up road who stoks heaps of that stuff .... was just hopeing that someone might know so i could avoid having to go back and fourth (doing massive service in one day and pre bulking parts lol)

I did all mine on the R33 but the R34 engine is probably bit different. I used mostly generic hoses straight and right angle sections - there is also one 135 degree section. don't forget the water line joins for the turbo feed line at the back of the head (if the R34 has that one). That is normally the first to leak - and the heater hoses and 4-way join at the bottom rear of the block under the intake manifold.

All-in-all....good luck. I'm glad I did all mine at once in the end.

You'll want to use genuine heater hoses (4 of them on the R33). These are intricately shaped and almost impossible to replicate with regular hose without kinking.

Edited by simpletool

When I did my greddy copy plenum I replaced all my vacuum lines with blue turbosmart ones.

Got a pack of 4mm, 5mm and 6mm which was good to replace all the vac lines. They come in black if you want to keep it looking stock

Yeah just from autobarn but there $60 a roll from there and you only get 3m

Try

http://www.tweakit.net/shop/index.php?cPath=57_452_464&osCsid=68u503ejfk37sfmm2m276p9qd2

I'm pretty sure it was 4mm, 5mm and 6mm but it may have been 3mm instead of 4mm

Yeah the qld section has been a bit dead lately. Haven't heard from many of the guys since they got back from airlie. Think next time we will organize it a bit better lol

I should have gone and scouted some good spots for photos, rookie mistake lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...