Jump to content
SAU Community

Recommended Posts

Just wondering if anyone else has experienced this with their 26s...

I recently installed one of the over cam cover, barrel style oil/air separators on my 32 GTR, was previously running the factory lines without issue.

Has been running the can now for about a week, got home last night after giving it a bit of stick (revved it to 7200 a few times max) and noticed oil on the driveway, popped bonnet and noticed the dipstick had popped out and allowed oil to blow on the drivers side inner guard...

Now, ive had motors in the past with busted pistons and broken ringlands and know that this can be an indicator that all is not well but i'm 100% sure that the motor is healthy, its a forged build and only running 11psi with knock reading no higher than 30 on average...

I run it about 500ml over filled with oil...

Im convinced this can is causing a restriction and creating excess crankcase pressure causing it to look for other ways out ie. via the dipstick tube...

Has anyone else had this issue with this style of separator?

Pic of install, any issues anyone can see???

atqm3o.jpg

2drzc7d.jpg

Edited by NSNPWR
Link to comment
https://www.sau.com.au/forums/topic/364214-oilair-separator-install-on-rb26/
Share on other sites

Ive got one runningperfectly fine.

Its got a pipe between the 2 hoses inside the cylinder/can. In that pipe there is a small slit venting into the can.

Try putting electrical tape around the dipstick so its a tighter fit. If that doesnt work try running the car without it and see if it still pops the dipstick out.

Cool, this is the same, small slit in the tube running through the guts of the can...I was running nothing previously and the dipstick never popped out, ever...

Does the install look correct? Ive seen one where someone had looped the 2 side breathers around the back so they connected up but doing this this wouldnt really provide any extra ventilation as such?

And I blew threw the can easy as before I fitted it so pretty sure theres no restriction in the can itself, my only concern with the install is the 90 degree elbow on the drivers side line from the PCV, not ideal.

I have the same setup on mine, just make sure all the hoses are still flowing easily, and the 90degree hose isnt kinking on the inside, also remove the pcv and clean it out with some throttlebody/carby cleaner, the valve may be sticking....good luck

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
    • After @Kinkstaah debacle, I'd never want to try and get it right 😛
    • The hood lines up with the fenders. The front bar doesn't perfectly line up with the fenders where the wheel arch is. You have to 'squeeze' the front bar 'in' as it wants to naturally flare out and be longer on the sides. There's a few threads where people notice this when they only swap a GTR style bumper and front bar. Unless you have genuine OEM items - you may be better served getting conversion kits. There are GTT bumpers to fit GTR hoods. There are GTR hoods (non genuine) to fit the GTT bracketry. MAY  
×
×
  • Create New...