TJR32GTS-T Posted May 22, 2011 Share Posted May 22, 2011 Hey guys, I've noticed abit of oil around the drivers side of the engine bay and it appears that it is coming out of where my dip stick goes in as the dip stick is popped out everytime I check, I am going to order a new dip stick because of heard that the seal can be rooted, what are the other causes of this and how bad can the problems be? Cheers in advance - trent Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/ Share on other sites More sharing options...
89CAL Posted May 22, 2011 Share Posted May 22, 2011 Other cause is crankcase pressure. I hope for your sake it's just the seal Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826284 Share on other sites More sharing options...
TJR32GTS-T Posted May 22, 2011 Author Share Posted May 22, 2011 I probably don't want to ask but what causes crankcase pressure? Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826328 Share on other sites More sharing options...
GODZ1LLA Posted May 22, 2011 Share Posted May 22, 2011 Worn bottem end Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826333 Share on other sites More sharing options...
The Bogan Posted May 22, 2011 Share Posted May 22, 2011 Hole in piston, or just a blocked breather. Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826342 Share on other sites More sharing options...
GODZ1LLA Posted May 22, 2011 Share Posted May 22, 2011 If you undo your oil cap (whilst engine is running) is there loads of smoke come out of it? Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826345 Share on other sites More sharing options...
TJR32GTS-T Posted May 22, 2011 Author Share Posted May 22, 2011 I will check, I just read that a incorrectly plumbed catch can could be an issue? I bought the car with one on have never seen a drop in it. Just a thought Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826362 Share on other sites More sharing options...
GT32 Posted May 22, 2011 Share Posted May 22, 2011 Yeah, a catch can that hasn't been installed properly can cause abnormal crankcase pressures dude. There's a massive guide somewhere on this forum about all the possible ways to correctly plumb in a catch can. Can't remember the thread name but just search "oil catch can" and it'll find something. Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826731 Share on other sites More sharing options...
TJR32GTS-T Posted May 22, 2011 Author Share Posted May 22, 2011 Cheers Phonz I'll have a squiz 2moro Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826763 Share on other sites More sharing options...
GT32 Posted May 22, 2011 Share Posted May 22, 2011 Here, already done the searching for you http://www.skylinesaustralia.com/forums/topic/129549-oil-catch-can-mounting-and-roughting/ http://www.skylinesaustralia.com/forums/topic/68174-catch-cans-again/page__hl__catch+can Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826774 Share on other sites More sharing options...
GT32 Posted May 22, 2011 Share Posted May 22, 2011 (edited) If you want to track down a new dip stick as well, go to Jerry again. He got back from Japan last week. I remember him having a crapload of RB dipsticks laying around his workshop. Edited May 22, 2011 by GT32 Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5826775 Share on other sites More sharing options...
TJR32GTS-T Posted May 22, 2011 Author Share Posted May 22, 2011 Sweet dude I'll give him a call, he posts his stuff doesn't he? It's just a pain in the arse driving to epping from the east, I'll check out another place I found this week aswell. Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5827012 Share on other sites More sharing options...
NSNPWR Posted May 23, 2011 Share Posted May 23, 2011 Can also try crimping the top of the dipstick tube a touch with some pliers to make it a tighter seal...but i'd be looking into why its doing it if its just started doing it out of the blue... Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5827188 Share on other sites More sharing options...
dorifticon Posted May 23, 2011 Share Posted May 23, 2011 To be clear, the reason the crank is pressurising is that blow-by is getting past the rings - but, that can happen even on a relatively OK motor. The fact that it's pressurising the crank to the point of the dipstick popping out may be a cause for concern. The pcv valve (positive crank case ventilation valve) is intended to vent the crank pressure. If the valve is gunked up, it won't be doing that job properly. Not hard to remove and clean, check operation. An incorrectly plumbed catch can will stop the thing venting if it's effectively plumbed in a loop. Basically you want to leave the factory route between the PCV valve and the inlet tract the same, and just intercept it at some point with a catch can. The basic route should not be altered. Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5827256 Share on other sites More sharing options...
GT32 Posted May 23, 2011 Share Posted May 23, 2011 I'm not sure if he posts anything but just call him and ask, you never know. I've never needed to get him to post anything as I've always gone in there because my gf lives around the corner from him. Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5827277 Share on other sites More sharing options...
TJR32GTS-T Posted May 23, 2011 Author Share Posted May 23, 2011 Cheers dorifticon, that explains alot, because I'm not that mechanically minded but pretty handy with tools how would I go about cleaning the pcv valve? A picture of an rb20 where the valve is would be awesome, I will also post a pic of the current catch can setup, Cheers Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5827708 Share on other sites More sharing options...
TJR32GTS-T Posted May 23, 2011 Author Share Posted May 23, 2011 (edited) ok here are a few pix and a diagram i drew alot of the oil in the engine bay can be explained by the outlet (which cant be seen in the ppic because it is at the bottom faceing the strut) on the catch can, but some of the spray appears to be from where the dip stick is Edited May 23, 2011 by TJR32GTS-T Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5827809 Share on other sites More sharing options...
simpletool Posted May 23, 2011 Share Posted May 23, 2011 (edited) 2 issues here: 1. Yeah that catch can isn't plumbed correctly ...but it's more just a case of it being 50% effective (at best) rather than causing a pressure build up. The two cam covers should be connected directly by a hose and the catch can plumbed into the line going out the right hand side of the diagram - between right hand side cam cover and intake pipe. 2. Unless.....the PCV valve isn't working. See the hose coming from the manifold and onto the T-piece? Is the 1-way valve working to stop manifold pressure from entering the cam cover at the t-piece. Sorry I only know how the R33 one works (which has a 1-way valve) at the cam cover. ohhh and where does that right-hand side pipe end up? hopefully in the intake before the turbo. ie stock location. Edited May 23, 2011 by simpletool Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5828091 Share on other sites More sharing options...
TJR32GTS-T Posted May 23, 2011 Author Share Posted May 23, 2011 Ok so if there was a hose bridging the 2 cam covers would it be efficient? They are kinda technically bridged but through the catch can. Also what do u make of the 3rd outlet on the catch can? I would imagine the catch can wouldn't fill because the outlet is at the bottom(see diagram) other setups I have seen have that outlet up the top with some sort of filter. Also I'm not sure how to check the pcv valve? Thanks for your input Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5828143 Share on other sites More sharing options...
simpletool Posted May 24, 2011 Share Posted May 24, 2011 (edited) There should be not outlet on the catch-can, other than the drain plug. That drain plug has the plug in it....right? Otherwise you are drawing in unmetered air through the catch can. Anyway, I've put some details in the photo. Dont' mind my other comments, I got a bit carried away. The PCV valve should only allow air to flow INTO the manifold, but not from the manifold and into the cam cover. You might have to check other threads for the RB20 PCV valve and where it is. you can test by blowing into it each way, Edited May 24, 2011 by simpletool Link to comment https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/#findComment-5829622 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now