Jump to content
SAU Community

Recommended Posts

Hey guys, I've noticed abit of oil around the drivers side of the engine bay and it appears that it is coming out of where my dip stick goes in as the dip stick is popped out everytime I check, I am going to order a new dip stick because of heard that the seal can be rooted, what are the other causes of this and how bad can the problems be?

Cheers in advance - trent

Link to comment
https://www.sau.com.au/forums/topic/365171-oil-shooting-out-of-dip-stick/
Share on other sites

Yeah, a catch can that hasn't been installed properly can cause abnormal crankcase pressures dude. There's a massive guide somewhere on this forum about all the possible ways to correctly plumb in a catch can. Can't remember the thread name but just search "oil catch can" and it'll find something.

If you want to track down a new dip stick as well, go to Jerry again. He got back from Japan last week. I remember him having a crapload of RB dipsticks laying around his workshop.

Edited by GT32

Sweet dude I'll give him a call, he posts his stuff doesn't he? It's just a pain in the arse driving to epping from the east, I'll check out another place I found this week aswell.

To be clear, the reason the crank is pressurising is that blow-by is getting past the rings - but, that can happen even on a relatively OK motor. The fact that it's pressurising the crank to the point of the dipstick popping out may be a cause for concern.

The pcv valve (positive crank case ventilation valve) is intended to vent the crank pressure. If the valve is gunked up, it won't be doing that job properly. Not hard to remove and clean, check operation.

An incorrectly plumbed catch can will stop the thing venting if it's effectively plumbed in a loop. Basically you want to leave the factory route between the PCV valve and the inlet tract the same, and just intercept it at some point with a catch can. The basic route should not be altered.

Cheers dorifticon, that explains alot, because I'm not that mechanically minded but pretty handy with tools how would I go about cleaning the pcv valve? A picture of an rb20 where the valve is would be awesome, I will also post a pic of the current catch can setup,

Cheers

ok here are a few pix and a diagram i drew

post-80927-0-70269300-1306129329_thumb.jpg

post-80927-0-08628600-1306129383_thumb.jpg

post-80927-0-68472900-1306129442_thumb.jpg

post-80927-0-55042300-1306129519_thumb.jpg

alot of the oil in the engine bay can be explained by the outlet (which cant be seen in the ppic because it is at the bottom faceing the strut) on the catch can, but some of the spray appears to be from where the dip stick is

Edited by TJR32GTS-T

2 issues here:

1. Yeah that catch can isn't plumbed correctly ...but it's more just a case of it being 50% effective (at best) rather than causing a pressure build up. The two cam covers should be connected directly by a hose and the catch can plumbed into the line going out the right hand side of the diagram - between right hand side cam cover and intake pipe.

2. Unless.....the PCV valve isn't working. See the hose coming from the manifold and onto the T-piece? Is the 1-way valve working to stop manifold pressure from entering the cam cover at the t-piece.

Sorry I only know how the R33 one works (which has a 1-way valve) at the cam cover.

ohhh and where does that right-hand side pipe end up? hopefully in the intake before the turbo. ie stock location.

Edited by simpletool

Ok so if there was a hose bridging the 2 cam covers would it be efficient? They are kinda technically bridged but through the catch can. Also what do u make of the 3rd outlet on the catch can? I would imagine the catch can wouldn't fill because the outlet is at the bottom(see diagram) other setups I have seen have that outlet up the top with some sort of filter.

Also I'm not sure how to check the pcv valve?

Thanks for your input :)

There should be not outlet on the catch-can, other than the drain plug. That drain plug has the plug in it....right? Otherwise you are drawing in unmetered air through the catch can.

Anyway, I've put some details in the photo. post-23086-0-67816600-1306199969_thumb.jpg

Dont' mind my other comments, I got a bit carried away.

The PCV valve should only allow air to flow INTO the manifold, but not from the manifold and into the cam cover. You might have to check other threads for the RB20 PCV valve and where it is. you can test by blowing into it each way,

Edited by simpletool

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Kinda glad I never got to this ..    https://www.facebook.com/groups/1483859159195077
    • @GTSBoy This method was able to get readings of -10 to -2, so it looks like its monitoring.  Now I need to figure out why the vacuum on the line provided isn't alternating with manifold pressure.  I went with 2 lines that an RB25 tuner recommended but I'll get a longer hose and try directly off the back of the manifold.  He may have been used to OEM intake setups while I have a DBW setup that removed the MAF and IACV.  
    • I work at a car detailing and tinting shop called Quark which gets all manner of German cars in usually (mainly due to a contract with Mercedes Benz Kita Osaka, BMW Nishinomiya and others) but every once in a while something special comes in, like a fully restored 1972 HS30 Nissan Fairlady 240ZG... The shop owner had immediately started applying film to the windows as soon as it was in the shop so the interior was completely covered in towels and plastic sheets. But I could get a few photos of the engine bay which was restored like new. Such an amazing car to see in pristine condition in Japan these days.  
    • Was going to say the car pulls up nicely everywhere, especially going into that last long right hander before the main straight. Looks like a lot of fun.
    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
×
×
  • Create New...