Jump to content
SAU Community

Recommended Posts

I currently have a r32 gts-4 manual, and want to put an rb26 into it. Ive searched through the forums and the topics were quite old, so would like to ask some advice on going about it. Is it worth doing these days or would it be better to just buy a r32 gtr? My situation would be, if i were to put an rb26 into it, i would go to a workshop.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/
Share on other sites

isn't that rb25de as is? Uses Rb20 injection etc???

Logic tells me turbo it and save big dollars, then slam stocky gtrs with it.

just confirm what motor u have and when i get to a pc I'll comment further...

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5828179
Share on other sites

I'm doing the Stagea swap. All wheel drive rb25, I agree with giving thought to a r 32 GTR. There is a lot of satisfaction in doing a swap, rb26s are getting cheaper. If you did both a rebuild and a transplant it will add up quickly. If you buy a 32gtr you could also be sorting out a motor and wear and tear any way. Most people will tell you GTR. I still think a gts4 with swap is interesting. With you Vic address have you looked at legalities of the swap? If you're buying a GTR why not get a later model 33 or better still 34 and just service it, a 32 is often a rebuild/restore etc.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5828217
Share on other sites

Id honestly love to have a GTS4 over a GTR, there is a certain element of surprise that allures me.

Personally, having done the RB20 and 25 things in the past, Id probably try to pick up the shortest ratio diff I can and keep the RB20. Having a good turbo on it that will max out at something like 230rwkw would make for a very fun and respectable car.

If I had to have more, I would buy an RB25 donk and retune the exact above setup with non vct cams. That would unlock about 20kw more and all bolt back into place.

Doing an RB26 is probably going to set you back atleast 5k more than the above and will still be in stock trim... Only just faster than above if not at all.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829466
Share on other sites

The GTS4 gives you the cheapest all wheel drive chassis, which you own already. This is an example of the type of Stagea set up you could buy. An upgrade turbo or highflow turbo, could see you performing better than a stock tired GTR. Potentially you could have the GTR performance envelope, and more money in the bank.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&item=370511948278&ssPageName=STRK:MEWAX:IT

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829509
Share on other sites

get a neo rb25 instead, better than half the thrashed rb26s out there

ultimately just sell the car and buy one with everything already done to it

He would have to track down a Stagea Neo all wheel drive RB25, agree better cylinder head and rods.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5829858
Share on other sites

I think the main point from the OP is that he'd be paying a workshop to do it.

Honestly, you may as well hand over your wallet, bend over and drop your daks.

I really can't see how you are going to come out ahead - $$-wise, kw-wise - getting a workshop to do the conversion. They charge for every hour they spend.

Even if you were doing it yourself in your shed it would be questionable. At least then the risk would be your time rather than $$.

If you are dead set on getting a GTS-4 conversion, wait for one already done to pop up, it's bound to happen.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5830042
Share on other sites

If he buys an r32 gtr, a move which makes sense to me, when the engine has a problem, (quite often clutch electricals, ATESSA, suspension as well), where will he go? A workshop as many on this forum do. He could remove the existing engine and donor engine, with friends and an engine crane source parts, to control his costs.

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5830210
Share on other sites

Do whatever makes you happy, whatever you want more. Nothing is cheap, yet I would be damned if I could not beat a GTR with a GTS-4 dollar for dollar. Performance and reliability as said above.

GL

Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5832626
Share on other sites

If you picked a sensible power figure above a stock GTR, I'm sure I would get there more cheaply starting with a gts4, than buying a gtr and upgrading it. Similar to the post above.You already have a GTR chassis with an unflared body. Consider the nz gts4 below.

Edited by WHITE gtt
Link to comment
https://www.sau.com.au/forums/topic/365273-engine-swap/#findComment-5832703
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...