Jump to content
SAU Community

Recommended Posts

  • Replies 3.6k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I know there's 8000 hicas threads but i think it's worthwhile to post a question on here rather than scour the abundance of info straight away. My hicas light on my dash has quickly flashed once on two separate driving occasions. I have no irregular steering symptoms but I have noticed both times it happened just after taking off (normal driving) and slight steering movements. The car was serviced on monday I figure it might be a bit of air in the system or something. Anyone got any ideas?

Hicas is not locked or bypassed all standard in that department. Will be happening soon though..

R32 HICAS and power steering is my arch enemy.

I've actually looked into get the whole lot turfed and having manual steering (DIY's online how to convert the stock rack to non-power assisted - though I'd get a workshop to do it). I'll let another workshop take a look at it before I go that extreme though.

I wouldn't mind manual steering. I love the feedback you get at speed.

Then I remember I occasionally daily the 200 with stupid sticky tyres on the front and realise it'd be a shit idea.

yu_tarou33-img600x450-11933022962.jpg

Where to get?

PSIParts make those n1 replicas.

Edit: $299 pp http://www.psiparts.com.au/detail.htm?ProductID=R33R%2DWGBL%2DCF

Also I got mine off eBay, no figment dramas at all

Even easier to use a paint scrapper, has a longer blade and has a handle as well.

OK..i have a big ugly caryard sticker on my rear windscreen its the chippy reflective vinal stuff :sick: .

I would like to remove it , im asking suggestions before i attempt this as i know it will get messy.

I was thinking of using Bug & Tar remover (worked wonders on the debadge.)

Please help.

I wouldn't mind manual steering. I love the feedback you get at speed.

Then I remember I occasionally daily the 200 with stupid sticky tyres on the front and realise it'd be a shit idea.

My power steering hasn't worked for probably 10 months, I'm used to it haha.

where to get cf film? :D

I can get it at cost and in a bunch of grades, colours, or metal look

thinking of a group buy in the future if interest is high enough

you can do a real carbon wrap on your existing blade too, the one you posted is a real carbon blade or covered in real carbon

the new carbon wrap can be purchased with clear coat already on it. , so matte or slightly shiny or wet look is available

Edited by sapphiregraphics

Even easier to use a paint scrapper, has a longer blade and has a handle as well.

the sinergy sticker you speak of ..lol is best removed with 3M or similar wax and grease remover soaked on a rag, do not use a razor except to pick up a corner to lift, they will scratch you glass.

just wet the rag and smear it on the edges lay the rag on the parts you want off and let it sit for a min then remove. wash afterwards with water.

not fatal to paintwork it will remove wax...lol and won't melt rubber. unless left on it for a while .

its a must have for any garage, it works on everything..lol

This trend of cf sticky concerns me. Luckily it doesnt look like the real thing.

I like the small CF sticky accents I've put on my R34. I don't think it's been overdone - just subtle (b-pillars & bottom of rear bar)

Mind you, I did this nearly 2 years ago now. Seems to be becoming more common of late, and 'too much'

I like the small CF sticky accents I've put on my R34. I don't think it's been overdone - just subtle (b-pillars & bottom of rear bar)

Mind you, I did this nearly 2 years ago now. Seems to be becoming more common of late, and 'too much'

there is some that looks real, I can show you real next to fake in a photo and you would be hard pressed to see the difference.

there is another option , Hydroprinting, that I was looking into. you can't tell the difference at all. I have vents done in that so you could see all three

real, hydro, wrapped side by side

I can get the seat material that is carbon weave in various colours as well, the good stuff , rated for salt water , UV rated, and burn tested for use on boats.

don't forget to wrap small parts you also need adhesion promoter, or it won't stay on in the heat, or on corners.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...