Jump to content
SAU Community

Recommended Posts

hey everyone,

looks like i have a water leak, i noticed it when my temp gauge started getting to 100 degree's on my drive home lol. Once the motor cooled down i checked my water level in the radiator which was very very low so anyway i looked under the car and noticed its dripping water somewhere on the back of the motor (still cant find it). its dripping onto the front pipe of the exhaust any ideas what it could be? maybe water pipe to the turbos? it looks like its coming from the turbo side of the engine.

any advice would be appreciated like always peeps :)

Regards,

Dom

Link to comment
https://www.sau.com.au/forums/topic/366295-r34-gtr-water-leak/
Share on other sites

I jacked the car up and found the leak, looks like its one of the fittings on a hard line feeding from the turbo into the block, hopefully the flare hasn't split and the fitting only needs tightening... crossing my fingers it doesn't get worse on my to get it fixed..

i had a similar prob on my s15. was a water leak but couldnt see anything in the driveway so it would only leak when driving.

result: turbo water line - the s/s manifold expanded and contracted on heat/cool and cracked the hard line.

fix: swapped for braided water line

do you have aftermarket manifolds?

anyways, goodluck with the problem. hope it all goes smooth

I had this problem like a month ago. Im near guarantee its one of the two small hoses (bout 4cm in length) at the back of the motor. You have to take the plenum off to get to it.

Heat the car up and get a torch or shine down the back of the motor and have a look if you can see where the water is comming out. If its one of those small hoses, replace both. You will need new throttle body gaskets and a new aac valve gasket. also get some hose clamps instead of the shitty ones that are on the std hoses.

Also doenlowd the inlet manifold page from the service manual. Its a bitch of a job.

I had this problem like a month ago. Im near guarantee its one of the two small hoses (bout 4cm in length) at the back of the motor. You have to take the plenum off to get to it.

Heat the car up and get a torch or shine down the back of the motor and have a look if you can see where the water is comming out. If its one of those small hoses, replace both. You will need new throttle body gaskets and a new aac valve gasket. also get some hose clamps instead of the shitty ones that are on the std hoses.

Also doenlowd the inlet manifold page from the service manual. Its a bitch of a job.

I have had the same lines fail on my car. It is possible to do them without the removal of the plenum.

I had as similar problem a few weeks back. Same drip location, but was a welsh plug right next to the turbo. Was a hard fix but sealed it with some aluminium cement until the motor comes out for a proper fix

Good luck hope its a easy fix

Finding leaks can be dam tricky sometimes. A leak thats up higher can convince you its actually leaking somewhere else in a difficult to repair spot.

I was convinced I had a hard line leak a few weeks ago too, till eventially the rubber hose that links the turbo coolant hard return lines back to the radiator top hose split and it became obvious where the leak was. I couldnt see it initially as the hose I am referring to is located under the air intake snorkel to the factory airbox.

The coolant leak was running from that hose, back along the pipe because the pipe is angled down towards the turbo.

I hope its an easy fix for you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...