Jump to content
SAU Community

Recommended Posts

Posting for a friend.

Hunter Dyno is celebrating the start of the cooler weather with a Dyno Day on the 11/06/11.

The day will start @ 8am and finish around 4pm. We are operating a first in best dressed basis so get in early to get a run.

Cost: $80, this includes 3 power runs and a print out on our Accurate Mainline Dyno

where: Hunter All Wheel dyno

1 Heather Street

Heatherbrae, NSW

2324

http://www.hunterdyno.com.au

Cheers

Link to comment
https://www.sau.com.au/forums/topic/366899-hunter-dyno/
Share on other sites

Did anyone end up going to this? What were your results?

Was not a big turn out overall. Rain kept people away.

An evo, a couple of subaru's, couple of v8's and 3 skylines.

1. White r34 Gtr - Left before i got a chance to ask.

2. Gunmetal r33 GTST - 131kw. Not sure what was going on here, there might have been a signifcant boost leak. i had to leave before i could enquire more.

3. Grey r34 Gtr vspec - None - Fail on my behalf - I couldn't get my front diffuser off to strap the car down (allen key bolts had been stripped and people were waiting...Big thanks to Steve for giving me a hand to get the rear one off.)

Link to comment
https://www.sau.com.au/forums/topic/366899-hunter-dyno/#findComment-5864899
Share on other sites

http://www.hunterdyno.com.au/Prices.html

Get Widge to do the tuning there. I think the price for the dyno day ended up being $60.

3 hrs? Could'nt of been just a power run. :/ You must've been unlucky lol. Everyone that i know who's been there has been happy with them.

I think the white Gtr only got 260kw.

Edited by worwor2
Link to comment
https://www.sau.com.au/forums/topic/366899-hunter-dyno/#findComment-5864912
Share on other sites

That was me in the white 34gtr, a white r32 gtr got 260, i wasnt hanging around all day. Only saw the silver 34 as i was leaving, would be good to get a look at your car mate.

Funny that, i said that about your car. It looked very tidy.

My car looks the part, but it has issues atm (turbos are pretty shagged, compression is down slightly an the ecu needs a good tune). I'm currently looking at the options for a rebulid/upgrade.

Eitherway, next time you see me say hello and "i'll show ya mine if you show me yours"

...that doesn't sound right at all....lol

Link to comment
https://www.sau.com.au/forums/topic/366899-hunter-dyno/#findComment-5866514
Share on other sites



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...