Jump to content
SAU Community

Recommended Posts

1.V-spec diff and rear cradle

2. Pipings.

3. maybe ill change the console to gtr monitor....

4. Attesa computer...Some wire havent been hooked up,, like the torque meter wire and a couple of unnessesary one.

5. Popped rivot a plate and mounted the computer in the boot. Will relocate the battery here too when I got some time.

6. Fuel pump controller....

7. Cluth cylinder, holesaw the firewall and put one on. part of the deal to convert a Auto to manual

8. Modified bonnet catch to suit GTR bonnet.

9. Modified hinges to suit GTR bonnet.

post-51895-0-56278700-1308479330_thumb.jpg

post-51895-0-66158500-1308479341_thumb.jpg

post-51895-0-77043100-1308479361_thumb.jpg

post-51895-0-34746600-1308479367_thumb.jpg

post-51895-0-67281500-1308479384_thumb.jpg

post-51895-0-35172000-1308479391_thumb.jpg

post-51895-0-32706600-1308479396_thumb.jpg

post-51895-0-32987100-1308479401_thumb.jpg

post-51895-0-80607300-1308479405_thumb.jpg

  • 3 months later...
  • 2 months later...
  • 2 weeks later...
  • 1 month later...

^^

laughing-smiley-014.giflaughing-smiley-014.gif

HAHA. I think all us GTT owners have subscribed to this thread.

Is there a way to have the GTR driveline convert into AWD as opposed to 4WD?

It's a lot of monies to do this conversion but I prefer a continuous AWD GTT as opposed to a 4WD convert.

  • 2 weeks later...

hi, i'm concidering doing this conversion myself thanks to this thread :) ive sorced the complete driveline and dash from a 34 vspec, but am going with a standard gtr engine as i'm upgrading the turbos to the t28s anyway XD

also gonna upgrade the a power fc or something like that.

is there any differance between the vspec 34 and gtt frames?

i'm hoping for a simple drop, swap and tune... what do you think my chances are? this'll be my first conversion and my mechanic's first on an r34...

:S

cheers in advance :)

It is not a drop in and tune.

Especially if it's your mechanics first time.

You need to make sure the ECU's (yes, all of them) are installed correctly. G-sensors, the works. It's not just a unbolt and bolt up affair.

You also need the gearbox and rear diff etc, add that the transfer case pumps etc. Cheaper just to purchase a GTR. You then get the wider guards etc and wheelbase - which is better again etc.

I'm not even sure the GT-t and GTR chassis are the same anyway, the GTR being better logically

+1.

From what I read the wiring/electrical aspect is the most difficult issue you'll face. I know a few dudes state-side that have done a GTR engine/tranny convert on a S14:

http://forums.nicoclub.com/95-awd-rb26-s14-kouki-t546132.html#p6228048

He said it was a BEITCH to do and expensive. If you have the time and money then I say go for it! If then, like R31Nismoid said, it's probably better to get a real GTR.

BTW, I was told that the R34 chasis are the same between the GTT and GTR. There are of course difference in certain areas relating to the frame (i.e. crossmembers, etc).

ive scored a vspec half cut fron and rear. they are the same car wich is a bonus XD

the only thing that has been taken out of it is the engine and the brakes. i've sorced another engine and some standard gtr brakes too. plus they even had the turbos of another vspec wich to my understanding are the same as t28's?

also looking out for a power fc. gonna be easier to deal with than a standard computer.

i'm taking everything out of the vspec and throwing it in my car.the only things that will still be gtt are the things i cant unbolt and the wiring for the cabin. even the brake system will be swapped over. the guy thats doing it said he'd do it for my 25gtt engine, gearbox and driveline. so really, its gonna cost me nothing to put it in :)

i thought about getting a GTR, but its still about 10k more than i can afford :(

thats alot to pay for some badges. i'm happy with the fun aspect and 250 a. w. killer wasps XD

thanks for the feedback guys, ill let ya know how it goes :D

  • 2 months later...

the swap will require alot of custom work. both mechanical and wiring........if you are asking someone to do it all, it will cost you alot and better of sell the car and buy the GTR. I took up this project simply to set a challenge to my self and see if i am capable of doing it. Which I think i did alright.

If you can read eletrical diagram, I would suggest you try it yourself if you have decided to take it on....

the experience and satisfaction is whats most important doing such a swap...in my opinion anyway..

  • Like 1
  • 4 years later...

Hey sorry for bringing up a very old thread, but did you have to modify the trans tunnel at all for the transfer case on the transmission? I am going to be doing this conversion and I have a R33 GTS4 as a parts car (it's crashed and not repairable but good enough for parts for this) which I can cut some of the transmission tunnel out if I need to but if you managed it without it then that makes things slightly easier.

  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What type of track driving will you be doing?  Do you have a set of class rules you need to abide by that will limit your rim / tyre width?
    • I've been reading a lot lately about unsprung weight and how beneficial it can be to reduce it for driving on the track, given my semi's only have another day or two in them I am throwing around the idea of some lighter wheels and a square set up. I have 265/35/19's and 245/40(?)/19 Federal 595's at the moment. The wheels and tyres are super heavy. I looked up my wheel weight online and got 14.5kg naked. Not sure if this was 8.5 (front) or 9 (rear) but that's a lot. I have also been reading about the benefits of a square setup. Much better rotation and potentially less understeer.  When I throw these together I'm thinking about a 17x9 or 18x9 square (preferably under 10kgs per wheel) with 245 or 255's. I can get some cheap 17x8.5 BMW M Sport wheels, they weight 10.5 kg's each but at 8.5 wide could probably only get 245's on them? I know they come with 255's from factory but semi's are a bit chunkier. Otherwise it will be aftermarket wheels in a 9" width. Most of the other BMW wheels are heavy unless you pay a squillion dollars for some M wheels.  Although, the E46 M3 Style 67's could be good but I'd have to buy 2 sets to square them up.  My car has a tickle over 400hp and about to put an LSD in also, is 245 a little thin for a square setup? It kinda feels that way to me. Also, is there any tangible benefit to having 18's over 17's? Is the footprint demonstrably bigger? From those of you who went to light(er) wheels after heavy buggers, did you notice it much?
    • Start with the R32 GTR wiring diagram. The ECU is essentially the same, so the pinouts are good. The details around ECCS relays, etc might differ a little bit, but the reality is that you need to get ignition power to kick the ECU so it powers up the ECCS relay which brings the rest of the ECU up. This also gives power to the other circuits that are needed to make the engine run, like the ignition coils, etc. All of this is visible on the R32 diagram and should give you a strong guide, even if it's not quite the same as the R33. As to specifics - I'm pretty sure no-one can help you from afar, as there is no way to know what mistake or omission has been made in connecting stuff up. It always turns out to be "LOL, I shorted something and an entire wire vanished out of the loom", or "We never connected X or Y main connector", or "shit, you mean I need to have that fuse installed?".
    • hello wanted some insight on what my problem could be so i swapped a RB26DETT into my r33 gtst used a R33 GTR engine harness and im using a haltech platinum pro. The car cranks but no start the ecu isn’t getting any power now im trying to find out why i cant seem to find any schematics  or diagram for the engine harness for the r33 gtr anything helps thank you.
    • hahahaa @GTSBoy that is my last resort. Like use a cardboard and cut it using the indicator as a reference. But I was winging my luck to see anyone had a spare bumper because drawing the outline off the hole is always easier and less chance of mucking it up
×
×
  • Create New...