Jump to content
SAU Community

Recommended Posts

Hey guys,

Just wondering if some of you could point me towards some of the better online businesses I can buy parts from to build my own PC, or even let them build it, if they can do it cheap. I used to know a few but simple cant remember them and google keeps sending me to crap.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/367344-building-a-gaming-pc/
Share on other sites

PCCG generally cost a little more than MSY

If you want to wait in a line (rather than online order), you can save yourself at least $100 if not more.

Depends on the parts you want as MSY dont stock a wide range, just a lot of the similar.

Thanks for all the info guys.

Getting a little lost and overwhelmed on what I should be buying. I pretty much want to run Battlefield 3, Diablo 3 and Skyrim all at high settings, with the ability to upgrade my PC in the future, and run any games that come out in the near future, even if that means playing them on lower settings.

Could I build a gaming tower capable of that for $1,500-2000? I've tried reading some articles but I get lost even doing that because most assume you already have a pretty good understanding of how a PC runs.

Thanks again.

I think the sandy bridge will remain at a similar price when the lga 2011 comes out later this year, but will drop significantly when the ivy bridge gets released next year.

But then again, I'm probably wrong anyway...

Prices will drop once the 6 series Nvidia stuff comes out and also when AMD's Bulldozer comes out in the next few months. And yeah go with PC Case Gear, they used to be a lot more expensive than MSY and CPL but they've become a lot more competitive in the last couple of years.

two on one boards are pointless, too hot and noisy, and the top end single cards in SLI / crossfire are faster anyway for the same price or less usually ;)

If upgrading from a POS now, go sandy bridge, otherwise wait for bulldozer / ivy bridge (mind you ivy bridge probably isn't until next year though!)

Apparently the difference between 2500K/2600K is SFA for games. If you use a lot of multi threaded apps, thats where you'll see a jump in performance.

Depends whether you care about the bragging rights of owning an i7 I guess.

Not sure about the i5 but all of this quadcore+ processor stuff is a bit useless atm with minimal programs making use of all of them. Remember when the dualcore was released?? Software and games took forever before starting to take advantage of the extra core.<BR><BR>That being said, I know most programs are capable of utilizing two cores so try buying a processor that has the turbocache feature; increasing frequency when only two of the four+ cores are being used.<BR><BR>And, for the record, Ivy Bridge is set for release March 2012. But the LGA-1366 successor, LGA-2011, is set for release later this year. I'm waiting for Ivy Bridge - by then it'll have full USB3.0 functionality (not semi like most motherboards on the market today) and PCIe 3.0. <BR><BR>EDIT - Only downfall would be video cards making use of the PCIe 3.0 capabilities - since theyre struggling to reach the limits of PCIe 2.0... but we'll see by this time next year anyway.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...