Jump to content
SAU Community

Recommended Posts

type B poncams to suit R34 GTR 260in and 260ex X 9.15mm lift, $650

stock R34 GTR v-spec II turbos,minimal shaft play, .53 front housing $450

stock R34 GTR v-spec II dump pipes, bell mouth design with port for exhaust temp sensor, $250

will post pics soon

pm me as this section moves to fast for me to keep up with

located at St Clair NSW

postage at buyers expense

Link to comment
https://www.sau.com.au/forums/topic/367368-r34-gtr-parts/
Share on other sites

  • 1 month later...

these are used poncams they will drop straight in no work required(you do need the R34 GTR CAS), you can how ever double check the gap between cam and bucket if you're worried but as they have the same radius as the stock cams with higher lobe centre they are drop in.they where working fine in my R34 only changed them to get more lower end cams, 250s for response aimed at track use

Link to comment
https://www.sau.com.au/forums/topic/367368-r34-gtr-parts/#findComment-5912216
Share on other sites

still got the stock turbos?i have a r32 gtr will these turbos suit the standard r32 manifold and dump pipes?

yes mate they bolt straight in and are a good upgrade for a street R32, though if your going to do it i would do the dumps to as the R32 ones are very restrictive

Link to comment
https://www.sau.com.au/forums/topic/367368-r34-gtr-parts/#findComment-5917080
Share on other sites

yes mate they bolt straight in and are a good upgrade for a street R32, though if your going to do it i would do the dumps to as the R32 ones are very restrictive

how much for the turbos?would your dumps fit in mine or i need custom?are they oil and water cooled or what? sorry

Link to comment
https://www.sau.com.au/forums/topic/367368-r34-gtr-parts/#findComment-5917155
Share on other sites

how much for the turbos?would your dumps fit in mine or i need custom?are they oil and water cooled or what? sorry

pm sent, yes turbos and dumps will bolt straight into the R32 33 GTRs no mods needed, they are watercooled same as 32 and 33, your right mate happy to answer any questions

Link to comment
https://www.sau.com.au/forums/topic/367368-r34-gtr-parts/#findComment-5917317
Share on other sites

  • 4 weeks later...

Hey Mike this blokes looking for R34 Turbos.

Sort him out will ya.

http://www.skylinesaustralia.com/forums/topic/374450-r33-or-r34-gtr-turbos-wanted/page__gopid__5975295#entry5975295

You can buy me a beer next time hehehe :)

Link to comment
https://www.sau.com.au/forums/topic/367368-r34-gtr-parts/#findComment-5975299
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...