Jump to content
SAU Community

Shaving Nissan Logo Off Brake Calipers

Hanaldo
 Share

Recommended Posts

Hanaldo Grand Master

Hanaldo

Posted
Posted

Hey all.

I'm after a more clean look for my brake calipers (not having issues with wheel fitment or anything like that) so I want to shave the Nissan logo off the side. Wouldn't go any further than that, I just want the flat face. Any suggestions as to how I could do that myself or would I have to take it to an engineer and get them to mill it off? Had thought of using a flapper disk but will that go through the metal?

Cheers,

Martin.

Daleo Grand Master

Daleo

Posted
Posted

Hey all.

I'm after a more clean look for my brake calipers (not having issues with wheel fitment or anything like that) so I want to shave the Nissan logo off the side. Wouldn't go any further than that, I just want the flat face. Any suggestions as to how I could do that myself or would I have to take it to an engineer and get them to mill it off? Had thought of using a flapper disk but will that go through the metal?

Cheers,

Martin.

Milling will definitely acheive what you're after, and you'll end up with a flat surface afterwards; something that will be very hard to get with a flap disc.

Also think about a belt linisher; would be nice to smooth out your machining marks after milling, but would easily do the job from start to finish if you've got a steady hand. Use a coarse grit belt to start, then finish with a 3M belt to smooth off for painting.

Hanaldo Grand Master

Hanaldo

Posted
  • Author
Posted (edited)

Thanks for the replies.

Yeh I figured milling is probably the best way to go about it. But I'm not sure who near me would do it or how much it would cost.

Problem with a belt linisher is... I do not have one lol. What about a hand held belt sander, do the same job? Would that do a better job than a flapper? A file would do the job but that's a hell of a lot of work and probably wouldn't get a nice finish.

Edited by Hanaldo
Hanaldo Grand Master

Hanaldo

Posted
  • Author
Posted

4" grinder did mine and then wet and dry (but i never got to the wet and dry) millings a waste of time and money,don't take any more than the letters off

Yeh that's all I want.

Thanks for the reply mate, that's what I was looking for :D

Legionnaire Collaborator

Legionnaire

Posted
Posted

It'd be interesting to see the result of your work.  

Post some pics when you're done with this "mod" as I'm still not sure whether calipers look better with or without logo. Are you gonna paint/coat them afterwards?

Hanaldo Grand Master

Hanaldo

Posted
  • Author
Posted

It'd be interesting to see the result of your work.

Post some pics when you're done with this "mod" as I'm still not sure whether calipers look better with or without logo. Are you gonna paint/coat them afterwards?

Yeh will do mate.

I'll definitely paint them. Not sure what colour yet though. Currently they are very dark blue to suit the GT logo. But I just got new bronze wheels and I want to get some blue wheel nuts. Haven't found any the same shade of blue, so I'm not sure if I should repaint them the blue they are now or a similar blue to the nuts. Decisions...

  • 2 weeks later...
Hanaldo Grand Master

Hanaldo

Posted
  • Author
Posted

Ok, so pics as promised...

I decided to use a 120 grit flapper disc on a 400w power drill instead of the angle grinder, as angle grinders and dye grinders are a bit too aggressive and end to take large bites out, making it difficult to get a nice finish. The flapper disc worked like a charm, albeit taking about 20 minutes of solid grinding to do each caliper. When the letters were gone I just hit the calipers with some 400 grit sandpapers to smooth them out, and the paint came out as you can see in the photo.

This is just after I started, I remembered to take a picture before I took anything more than paint off:

IMG_0827.jpg

And this is the finished product:

IMG_0831.jpg

This is the exact look I was going for so I'm very happy with it.

Hanaldo Grand Master

Hanaldo

Posted
  • Author
Posted

VHT mate. I actually repainted them with the exact same paint I had before, the finish doesn't change much. Obviously it loses a bit of shine, but if you do it right then it lasts.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...