Jump to content
SAU Community

Recommended Posts

Hey guys got a gtt and recently got a Kakimoto cat back.

When I give it some sometimes I hear a pop like a back fire, and when I'm slowing down via transmission I get that gargle noise that you hear all the v8s have (to a lesser extent ofcoarse). Just wondering:

If these things noises are bad?

What causes them?

And would I see much power gains/other benefits with 3" turbo back with a stock cat or would the stock cat act like a bottle neck so no point getting 3" turbo back??

Jarrad

Link to comment
https://www.sau.com.au/forums/topic/371016-exhaust-questions/
Share on other sites

mild improvement with the 3" turbo back but you really should replace the cat while you are at it.

the pops are just unburnt fuel igniting in the exhaust, nothing to worry about.

this,

Could also be a leak in the exhaust system. go over the joins again and check the bolts are done up nice n tight..

Point 1. Cats are relatively cheap.

Point 2. Stock cat is tiny.

Conclusion 1. Get a bigger cat.

Question 1. Pop/backfire is on th rev limiter? Or when you go off throttle to on throttle?

Question 2. Gargle means what? You mean large exhaust low flow resonance like you'd expect in a big pipe?

I see, will a high flow cat increase noise alot though??? I don't really want much more of a drone while driving I hate that noise :P

Would a 3" cat be good enough or do you think a 3" high flow should be put in place??

Tha ks for you time Titan

Hmm alright I'll check that Aaron, I'm pretty sure they got te apprentice to tighten them up, he didn't look the strongest :P

I'll check it soon thanks.

Yeah pretty close to redline from just with foot to the floor.

Haha yeah I think I do, I thought thatd be nothing but I thought I'd ask.

I think I'll replace the cat too if it doesn't increase noise which was said in my last post.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...