Jump to content
SAU Community

Recommended Posts

About the only thing that you can adjust is the height of the clutch pedal. I doubt that this will have much impact on the actual grab point.

Are you concerned about the grab point? If so, try bleeding the system, there may be air in there. Remember, there are 3 bleeding points on the R33.

Neither am I ........ WICKED avatar dude.

 

There may be some adjustment on the slave mounting slots/holes, but it has been a while, but the best bet is a bleed first

Yeah cause at the moment its grabbing down low at a nice point but as it wears i expect it to grab a bit higher....And i was looking at the adjustment and if it had any for this reason..

:P

there is an adjustment at the top of the back of the clutch pedal.. hard to get to. all you do is undo the bolt the undo the rod and do up the bolt again. i think thats how you do it... i didn't do it, my mech did it.

It's hard to explain without pictures.

Actually, if you want to include the master cylinder, there are actually 4 bleever valves on the R33.

There are 3 bleeder valves that are only accessible undernieth the car. If you follow the piping from the master cylinder:

It depends on what you are doing. I drained the whole hydraulic system meaning that when I filled the system up again, I had to use the three bleeder valves

...Sorry...don't know what happend there..it posted my reply before I finished,,

Continue...

If you follow the piping from the master cylinder:

- there is a valve just after the bend heading towards the back of the car on a junction block

- there is a valve on the junction block just before the 'u' bolt where the piping changes direction heading towards the slave cylinder

- then you have one on the slave cylinder

If you are simply bleeding the system, just concentrate on the slave cylinder, get all the air out there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...