Jump to content
SAU Community

Recommended Posts

Vic Stageas.

Finally got this thread happening.

Thanks to everyone who contributed by putting in a date and place into the recent Poll.

As you are all aware, the 21st of August was chosen for a nice cruise up to Arthur Seat!

Details

Sunday 21th of Aug

10:30am meet 11:15am departure.

Monash University Clayton Wellington Road Carpark.

We will drive towards and along Nepean Hwy until we meet a first meet point at Schnapper point. This will alow us to re group with anyone that has fallen behind.

Then make our way through to Arthurs Seat Rd to the top of the mountain.

There is quite an interesting maze here, and a Fantastic Restaraunt to sit and have lunch! So its good for the Family to come along!

please be advised that this is a drive, not a race, drift contest, skid pan, or touge. if you wish to be a hoon, DONT!

Will have maps/directions ready on the day.

You should bring;

  • Pen marker
  • Walkie talkies
  • Full tank
  • Your Cars
  • A Camera(if you have one)
  • Anyone else who wants to tag along.

This is the cruise Route Included are the directions.

Arthurs Seat Cruise.pdf

Hope to see you all there!

Thanks people!

Link to comment
https://www.sau.com.au/forums/topic/372655-vic-stagea-cruise/
Share on other sites

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...