Jump to content
SAU Community

Recommended Posts

I agree with Cam, dump/front pipe, EMU and tune for 20psi on the stock turbo. As long as the oil restrictor doesnt get blocked it should last, mine did for over 4 months. Then save for the turbo rebuild...

(Aaron, I think 2.5mm would be better)

i was talking opening it up in general. mines open 2.5 if i remember right.

  • Replies 151
  • Created
  • Last Reply

Top Posters In This Topic

Alright. This is the smarts I like to hear. Anywhere that you guys can link me to more info on the oil restrictor? Dunc told me to do that too, so I'm guessing it should be at the top of the priority list.

iamhe77, ended up getting the black Aero kitted one from Wodonga.

Edited by jasevr4

Alright. This is the smarts I like to hear. Anywhere that you guys can link me to more info on the oil restrictor? Dunc told me to do that too, so I'm guessing it should be at the top of the priority list.

iamhe77, ended up getting the black Aero kitted one from Wodonga.

Yeah, that and the dump/front pipe.

Is the Nismo the one with the two square tips? If so leave it. It is a damn good design and a lovely note :)

Alright. This is the smarts I like to hear. Anywhere that you guys can link me to more info on the oil restrictor? Dunc told me to do that too, so I'm guessing it should be at the top of the priority list.

iamhe77, ended up getting the black Aero kitted one from Wodonga.

i dont think theres an exact write up. its the banjo bolt on the oil line from to the turbo

If memory serves, its actually the Nissan Sports Muffler - not the nismo one actually

Oh, if that's the case.... upgrade it.

2.5" exhausts have no place on our cars. Bang for buck is the Blitz NUR. Quiet as stock and free flowing 80mm pipe.

Yeah I'm just going by what I've been told. It's the one where you can press a button and it becomes quieter/louder. Not a twin tip.

Has anyone had an Emanage tuned in SA from here?

Yep, Nissan Sports Muffler. Its what I've got in my car.

No ones tuned with e-manage in SA yet; Ive got one sitting on my shelf for, Im slowly organising all my parts & funds to get that done at Willall

Yep, Nissan Sports Muffler. Its what I've got in my car.

No ones tuned with e-manage in SA yet; Ive got one sitting on my shelf for, Im slowly organising all my parts & funds to get that done at Willall

should just drive down to melbourne with bigkev and big fella, you could be big dunc lol

A good bet would be to take a road trip to melbourne to get an eManage tuned.... or get a group together and put Cihan (www.etuner.com.au) up for the night so he can tune a few while there ;)

I made over 200awkw on a 2.5 inch dump/front pipe mate, with the stock turbo... :whistling:

and here I was thinking that your initial 200kw was made with the Kamikazee turbo back that came with your car.

So if you had to start again, would you leave the 2.5" pipe on the car?

What are you guys basing the oil restrictor needing to be enlarged on? Has anyone measured the oil flow out of the turbo? Im assuming if its enlarged to much it will get too much flow and possibly blow the oil seals in the turbo. Im interested in this mod if it helps and if this is in fact a problem with the turbo.

I wouldn't have thought Nissan would run a smaller restrictor than needed.

What is the standard size of the restrictor? Is it easy to get that banjo bolt out while turbo still fitted in the car?

Cheers

What are you guys basing the oil restrictor needing to be enlarged on? Has anyone measured the oil flow out of the turbo? Im assuming if its enlarged to much it will get too much flow and possibly blow the oil seals in the turbo. Im interested in this mod if it helps and if this is in fact a problem with the turbo.

I wouldn't have thought Nissan would run a smaller restrictor than needed.

What is the standard size of the restrictor? Is it easy to get that banjo bolt out while turbo still fitted in the car?

Cheers

So don't do it, no-one is forcing you.

Fact: Aaron blew up two turbos because his restrictor was blocked.

Fact: I ran 20psi on the stock turbo just to prove it wasn't going to crap its self or shear the ceramic off the shaft.

Nissan don't care what happens after the warranty has expired and cant be held responsible for sub-standard servicing or oil selection causing a build-up of crap on the inside of you engine. The stock restrictor is 1mm and obviously blocks very easily.

The front banjo bolt is the restrictor and can be removed with a little patience. The turbo seals are steel so I dont understand how you would think they will "blow out". Drilling it out is mandatory if upgrading to a bush core highflow btw. :thumbsup:

So don't do it, no-one is forcing you.

Fact: Aaron blew up two turbos because his restrictor was blocked.

Fact: I ran 20psi on the stock turbo just to prove it wasn't going to crap its self or shear the ceramic off the shaft.

Nissan don't care what happens after the warranty has expired and cant be held responsible for sub-standard servicing or oil selection causing a build-up of crap on the inside of you engine. The stock restrictor is 1mm and obviously blocks very easily.

The front banjo bolt is the restrictor and can be removed with a little patience. The turbo seals are steel so I dont understand how you would think they will "blow out". Drilling it out is mandatory if upgrading to a bush core highflow btw. :thumbsup:

Take it easy mate, Im not attacking anyone here, just asking.

I read the link that Jetwreck supplied and noticed they are talking about a Garrett BB core. The guy was increasing the size of the restrictor when all Garrett BB cores have a restrictor built into the oil feed in the core. This makes it pointless to drill out the banjo for that turbo as Garrett have already set the flow needed.

If the standard turbo is high flowed with a new bush bearing core I can understand why you need to check the flow and adjust the restrictor to suit the manufacturers flow rates.

Just working out what circumstance it was advised in this thread to do it. If the turbo is stock I don't see the need. Just remove the banjo and clean.

Just gathering more info for myself cheers.gif

Edited by slippylotion

Take it easy mate, Im not attacking anyone here, just asking.

Just remove the banjo and clean.

Just gathering more info for myself cheers.gif

It's more of a safety issue.....a 1mm hole is a lot easier to block than a 2mm ect......cleaning it may not fix the problem as there may be more shit sitting around the engine that will block it at a latter stage(e.g. Aarons oil filter res)

I was told by my turbo builder to open up the hole as the Garrett BB set I have already has a restrictor in it.

BTW.

P.S. Chill pill guy's.....ffs the guy(radaladelaidian) was only asking a question about why we were doing it......there has been a lot of what I would call rude response's lately(I know I am one to speak!!blush.gif)......I know there are a lot of new guys coming on here now and maybe its the way they write responses but I am sure they did not wake up in the morning having the objective of pissing you off by the end of the day.....

well maybe Aaron and Iain wake up with that thought towards each other....I think it's just sexual tension though! :P

Edited by Jetwreck

yeh i had an oil blockage near the pump. and it couldve been the reason it kept blowing. but ive fixed that since, and got more power after another tune.

i'd suggest doing it, but as scott says no ones forcing you, but your turbo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...