Jump to content
SAU Community

Recommended Posts

101 motorsport in slacks creek, have done a great job on mine and a few mates cars.... they have just moved shops though and it appears they havent sorted the phone out yet/ updated the web site

erd at yatla - halfway between brisbane and gold coast

Use ERD at Yatala for any mechanical work, they can't do tuning however - No dyno.

I use EFI around the corner from ERD. Great guys who do phenomenal work.

Myself and about 10 of my friends all get our cars tuned at Matty Spry at PITS.

Never had a drama and cars always drive a lot better than they did before.

Another mate has had his RB26/30 tuned by Mark Jacobsen at Godzilla Motorsport and he did a good job also considering the car spends a lot of it's life near or on limiter and never had an issue until it spun a bearing. Going back there once it's rebuilt too for another tune. He runs a Vi-PEC which is Mark's preferred ECU as I understand.

GT Auto Garage has also been highly recommended to me by several people I know that are customers of theirs. I have a HKS F-CON V I have been thinking about running in my current car and they are the only place in QLD that can tune these and seem to have very good results with them.

They are basically the only 3 places I would consider in QLD.

Edited by «Cyph3r»

yeah i was thinking along the lines of EFI, or GT Auto Garage, Ive spoken to a few different people in the know and they have said the Autronic, or HKS fcon thanks heaps guys ill have a look at these 2 guys !!! and has any one run either of these 2 ECU's? and can give me any feed back on them...

Had a power fc tuned by Matt Spry at PITS a few years back for the rb25 180. It had heaps of running problems going in with a different plenum etc but ran beautifully when I got it back. Power everywhere and perfect manners around town. I could not believe the difference and how nice it was to drive.

Also had Dyson Rotary from near Harbour Town run up a Microtech tune on the same car later with bigger turbo & fuel system after the power fc got stolen :( and that went fairly well too believe it or not. It was a bit more hairy around town and at partial, but the Microtech's are more like that anyway plus it was it was in a more advanced state of tune too so not a fair comparison.

There are actually quite a few good tuners around this area which is lucky...

EFI did a very good job on mine. Good power, Great response, Well behaved at traffic speeds and good on fuel. Most of the guys in the club use them and every one is happy.

+1 EFI are the best!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The speedo's can be very conservative, when my Mazda NC MX5 speedo is showing 118kph, the GPS, and a calibrated radar.... cop mate.....hits me at around 110kph +/- 1 or 2 kph, and that is on a 215/45 17, stock tyres size is 205/45 17 as well, so weirdly conservative with stock tyre size When my Commodore speedo red 116kph GPS had me at 110kph After doing some offset and clearance measurements to see what can fit the NC on 17x8 +40, without guard rolling or rubbing anything at my current ride height, I've decided that when my tyres are toast, I'm going to fit 225/45 17 and see where that gets me IRT actual speed of my speedo and GPS/radar From the online calculator I should be still be doing around 5kph under an actual 110kph when the speedo is showing 110kph My ADHD requires that when I'm doing 110kph on the speedo, that the actual road speed is actually really close to that, and not alot slower And going from 205 to 225 still keeps the car within the %/mm allowable in the NSW vehicle rules and regulations, which is nice, as long as I'm looking at the latest version that is.....LOL https://www.nsw.gov.au/sites/default/files/2021-02/RMS-13.464-Light-vehicle-modifications-Vehicle-Standards-Information-No-6-November-2013.pdf
    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
×
×
  • Create New...