Jump to content
SAU Community

Need R33 Stock Front Bar To Pass

G3TINQ

By G3TINQ,
in Victoria

 Share

Recommended Posts

G3TINQ Collaborator

G3TINQ

Posted
Posted

Hey guys need a stock front bar to pass Vic roads or ny1 know how to make it Higher? It's just hitting the wheel the copper used? I could borrow it of ya or bye it up 2 u need it by this week I'm located in noble park but I work at oakleigh contact me on 0466 910 750 or pm me thanks help will be much appreciated

Link to comment
Share on other sites
JPCR33 Proficient

JPCR33

Posted
Posted

I take it you got done for being too low?

If you have an aftermarket body kit plus low springs you are fine because that still gives you 10cm clearance

If you have an aftermarket body kit plus ultra low springs then best bet is to change springs to lows or something that will give you enough clearance.

If you have coilovers just wind them up till the car is above 10cm of the ground

No point borrowing a standard front bar to clear and repeat the process again? Do it once do it right. Unless you want to return to standard front bar.

If your keen on changing back to a standard front bar...Check the for sale section on the forums, or post the topic in wanted to buy section on the forums.

Good luck.

Link to comment
Share on other sites
bluey33 Experienced

bluey33

Posted
Posted

Can use blocks but vicroads may see them. Go to any Audi service centre and ask for some blocks they remove from cars at Pre delivery. This will do the trick but gives shit ride and can get smashed up so don't drive to far with em in. Other car manufacturers may use them but Audi definitely do.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      Rb25 Turbo Upgrade, All Dyno Results

      By TurboTapin · Posted

      2.8L Stroked S1 RB25 Fully built block (Spool&CP) and head (Ferrea & Kelford 272's). Hydro lifters.  Precision 6466 Gen2 1.00 T4 Divided. 2x 40mm Turbosmart open dump gates.  DW 1200cc injectors 2x AEM 320LPH Pumps Haltech Elite 2500, IC7, WB1, TC8, Etc.  4" Downpipe, 3.5" Catback.  94AKI (101.5ron) Pump gas + WMI (2x 1000cc nozzles) 463rwkws @ 27psi on a mustang roller dyno. 
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      I finally got it on the dyno today and luckily it stayed in one piece! It wasn't without its dramas though. First off, sent my power steering belt to the moon around the third pull. Scared me half to death. Tuner laughed and mentioned that often happens with RB's... I may need to look into adding the Ross power steering idler, or something a long those lines.  Second issue that came up was about 2 hours in, we realized the VCT wasn't working and had to go back through the timing and knock threshold once it was fixed (I had botched setting up VCT). That waisted a good hour or so. I was surprised to see that with VCT working, we saw a ~38rwkw difference across the powerband. More then I would of expected.  Without further ado, made 463rwkw@27psi. Not the numbers I originally set out after, but still more then enough to kill myself and I'm very happy. Mustang roller dyno's are known to be heart breakers compared to other dyno's. Two things that limited me, first was the hydraulic lifters/7600rpm cut. Tuner was adamant that I was losing out on a lot of power up top because of it. Second was the pump gas & WMI. He wasn't 100% comfortable tuning with WMI, and was honest about it. He stated he's more confident on E85/Race gas. I look at this as a positive as it leaves me a lot of room for improvement. All in all, very happy! I need to see what I can do about that rev limiter... I use to rev my stock RB20 to 8000rpm and now I have a fully built head that I only rev to 7600... It's bugging me.  Don't mind my fantastic picture/filming skills.  RB28 - Dyno (1).mp4      
    • ianp
      Share Your Euro!

      By ianp · Posted

      The Daily - 2011 Audi A5 And the camper VW transporter T5          
    • Milkmun
      Newbie from Geelong, Victoria

      By Milkmun · Posted

      Wow mate that's huge, congrats. Glad you found better people to deal with and all seems like it's going in the right direction.
    • The Bogan
      What Is A Good Setting For Street Camber?

      By The Bogan · Posted

      The best setting for street is what gives the best tyres wear for your driving style Different tyres like different camber You want the whole surface of the tread to wear flat, if the inside of the tyre is wearing more than the outside reduce camber settings For toe, have the minimum amount to give the handling you want Caster, from my experience if you can adjust it, is as much as you can get without clearance issues And while -2.5° of camber on the front might work well with good tyres for "spirited" cornering, it may be too much for a street car Lots of front camber will effect braking Just like to much rear camber will effect rear traction (rwd), and braking  When I set my Bogan Cruise Ship (VX SS) up for drags I tested how much tyre width I actually had in the rear by doing a hard launch (skid), it originally had -1.5° in the rear, and you could see that the tyre wasn't putting down alot of the tread, I maxed out the settings to get as little camber as I could with the OEM adjustment and some camber bushings and got it down to just under -0.5° with 0 toe, that gave me a fair bit more "rubber on the road" and helped it hook up for my 60' and my 0-100kph And with -1.5° in the front the big old boat handles fine on the street and my tyre wear is nice and even on both front and rear tyres (currently Hankook RS4's) As for semi slicks at the track, again, it depends on alot more IRT the suspension, the track and lots of other things, so, I'll leave that up to people who have more experience, especially with a AWD In saying this, street settings are pretty easy, just look at the tyre wear Meh, Necro thread, it's late at night, and I has been drinking beer
×
×
  • Create New...