Jump to content
SAU Community

Recommended Posts

hey guys i brought a dodgey turbo smart boost controller off ebay and i fitted it today and turns out i took off and it had way 2 much boost and the car popped and just stopped spooling n boosting, iv removed it and connected it back to the factory solenoid but nothing still happens, has anyone had this issue before?? i miss boost already :(

Link to comment
https://www.sau.com.au/forums/topic/375221-car-doesnt-spool-up-after-big-pop/
Share on other sites

If you pop an intercooler pipe on a factory ECU/AFM equipped R33 GTST it will not idle and blow black smoke like crazy.

If the car idles fine and drives perfectly fine, just doesn't make any boost, you have blown the exhaust wheel on the turbo.

If you pop an intercooler pipe on a factory ECU/AFM equipped R33 GTST it will not idle and blow black smoke like crazy.

If the car idles fine and drives perfectly fine, just doesn't make any boost, you have blown the exhaust wheel on the turbo.

That's pin points it, so in other words I replace the turbo?? Should I do wastegate as well just to make sure?

If you pop an intercooler pipe on a factory ECU/AFM equipped R33 GTST it will not idle and blow black smoke like crazy.

If the car idles fine and drives perfectly fine, just doesn't make any boost, you have blown the exhaust wheel on the turbo.

depends on how the hose is popped. if it is still mostly on there then it can simply leak under boost but idle fine, but it will run pretty crappily under boost.

that said, if the wastegate actuator is stuffed then it may run no boost. normally though it's the other way round and it will run unlimited boost.

i'm not saying the turbo isn't stuffed, just giving other possible causes

  • 1 year later...

i think i might have same problem with a couple tiny diffrences, i blew the exaust manifold gasket and i can get to about 2psi but the rest sound the same. changing turbo out tonight hopefully fixes the problem

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...