Jump to content
SAU Community

Recommended Posts

Hi Guys,

A few minotiry probably knew about a idle issue i have been having over the past few months, so ive finally been able to check my car in for a diagnosis. After a number of weeks looking at every nook and crany of the intake system we believe the issue is actually related to the bearings of the throttle bodies. We have replaced the AAC, TBS and cleaned out most of the intake side but still seems to be idling at 1500rpm. Replacing the throttle bodies has proven a bit to expensive and unreliable to be worthwhile so i thouhgt id take this chance to get a whole new intake system.

What are peoples experiences?

Greddy - still retains the ITBS?

Hypertune - Big $$ but supposely the best money can buy

Nismo - any experience?

ect

Any help much appreciated.

Edited by Jap_Muscle

At the factory they use a black sealant (maybe it starts off a different color and turns black who knows) on the ITB butterfly shafts to stop air being sucked in.

Yeh i did some googling and it looks like ill need to do what they did in this.

http://www.skylinesaustralia.com/forums/topic/286728-nissan-gtr-high-idle-and-throttle-body-fix/

and get my hands on some of that Tomei Throttle coat

You could also pressure test the entire intake from the intercooler inlet pipe to identify the leak under pressure. Or when the car is idling, spray brake cleaner around the butterfly shaft ends and listen for a change in engine speed. It will be very obvious when you find it.

If you dont find a throttle leak (or gasket leak in that area), move onto either a pressure test, or block off all the hoses that are vacuum related such as brake/clutch boosters, charcoal canister etc until you can stall the engine or get the idle to drop.

So ive taken some pictures of the throttle bodies and as you can see they are pretty dirty.We plan to reset the throttles after cleaning the inside of the bore out including the special paste that seals the flaps shut. We will be applying some new Tomei Throttle Coat paste which should fill up any gaps there may be.

However the original concern that we had was that the bearing (picture 3, cant really see as its behind the screw) seems to be letting air into the chamber.

Any thouhgts on all this?

img0563vl.th.jpg img0561e.th.jpg img0559p.th.jpg img0558do.th.jpg

img0557e.th.jpg img0556p.th.jpg img0555st.th.jpg img0554ga.th.jpg

Edited by Jap_Muscle

How can u tell if air is getting in through the bearing?

There is prob a seal in there so if you can dismantle have a look. Can always refit and spray lube around it to see if it goes away.

Edited by eightsixboy

There is a seal that stops air getting in through the bearing under high boost. These seals can push out. They cant be ordered from nissan though.

You can buy inserts to put in behind them to lock them in though.

Ive seen them on ebay usa.

This might sound absolutely ridiculous and outrageous.... But here goes;

How about a second hand set of throttles for a pittence instead of a whopping dollar value on an aftermarket setup?

Crazy I know... But if your certain your throttle setup is the problem, why not have your stab in the dark at a couple of hundred $ instead of a couple of thousand $??

There is a seal that stops air getting in through the bearing under high boost. These seals can push out. They cant be ordered from nissan though.

You can buy inserts to put in behind them to lock them in though.

Ive seen them on ebay usa.

Ok i'm on my computer now, this was meant to mean;

There's a little rubber seal on the shafts that seal off the throttle bodies. Under higher boost conditions, these seals can push out and cause a tiny leak which is noticeable during idle.

There is a company in the US that makes hard plastic/nylon stoppers that fit in behind these seals to hold them in and stop them from popping out.

If your seals are good, from what i can gather, this is a good modification and i'll be doing it to my engine once the rebuild gets under way.

You cannot buy these seals from Nissan. I think someone already mentioned this.

This might sound absolutely ridiculous and outrageous.... But here goes;

How about a second hand set of throttles for a pittence instead of a whopping dollar value on an aftermarket setup?

Crazy I know... But if your certain your throttle setup is the problem, why not have your stab in the dark at a couple of hundred $ instead of a couple of thousand $??

I hear what your saying buddy. Few reasons.

One is trying to source a 2nd hand set which can be a hassle.

Being second hand who really knows how long these things will last.

Buying brand new is almost just as expensive. $1500 for a new set of throttle bodies

Being a 3L build the setup would benefit very much converting to a single 90tb, so why not. Obviously if i can fix the issue, happy days. But the last thing i want is to piss thousands of dollars in labour for trial and error.

Being a 3L build the setup would benefit very much converting to a single 90tb, so why not. Obviously if i can fix the issue, happy days. But the last thing i want is to piss thousands of dollars in labour for trial and error.

Actually thats not quite true.

Engines that benfit from single throttle intakes are the ones that have massive cams and as a result a poor vacuum at idle and at low engine speeds.

My RB315 with stock cams pulls -20mm more vacuum than a stock RB26 at idle with stock cams. More displacement directly increases low speed vacuuum, and as a result makes the engine easier to tune. The other side effect of and engine with a poor vacuum is that your brake and clutch booster doesnt work all that well if you are driving sedately. Because the engine will only pull a good vacuum level on a gear shift from a high rpm.

So if your 3lt is running 272 or larger cams, then yes you will make the engine easier to tune and nicer to drive with a single throttle plenum. If you are running 260 or less cams, then there is no tuning or drivability benefit. Instead, the engine will actually have slightly less throttle response, because there isn't a plenum full of filtered air at atmospheric pressure directly on the other side of the butterflies only a few inches from the intake valves. Granted we are only talking a tiny difference in throttle response, but it is there.

Have you pressure tested the entire intake system yet to identify the leak? I have tested my intake system at over 35psi and the stock throttle shaft seals don't leak. Once its pumped up the only way air can escape is to blow past the piston rings on the cylinders that have open intake valves.

I am pretty sure the xs-engineering seals arent available any more either. I contacted them once a few years ago when I had a shaft seal leak on my R33 GTR. It used to make a whistling noise at idle. I ended up spraying it with some INOX when testing for leaks and the sound went away forever, and so did the leak. I guess the INOX somehow helped the seal seal again, possibly made it expand a little.

One more thing. Is this a built engine that has been apart before? If so its possible that the wrong alignment dowels have been used in the throttle bodies to align the plenum and base plate.

There are two length dowels in the engine that will fit the throttle bodies. Using the slightly longer dowels that belong under the throttle assembly(that the throttle cable connects too) in the throttle bodies will prevent propper compression of the gasket, because they bottom out in the alighment hole. So you get a leak.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...