Jump to content
SAU Community

Recommended Posts

  • Replies 412
  • Created
  • Last Reply

Top Posters In This Topic

$25 for CAMS is pay on the day, chief. Has nothing to do with SAU.

Oops. Already transferred, figured SAU had to pay the money to CAMS anyway on my behalf. Can I just get a refund on the day?

yeah Ryan that shouldn't be a problem

less our withdrawal fee of $25

Sure Steve, do I get a free CAMS day licence when I pay the withdrawal fee? :P

Front shocks, pads and rotors in yesterday, rears go in next week. I may get everything fitted in time at this rate!

I still gotta refit my rear subframe.

And fit my injectors.

And cams...

And fuel pump...

And have my exhaust made...

And my intercooler piping...

And my catch can...

And get it tuned...

So I've basically achieved nothing.

You've been working on fixing that diff for longer than I've been scratching my about the Borg Warner though...

Just spent more time thinking of which direction to really take things into.

Car is at boostworx at the momemt mate, getting a few issues looked at. Hopefully will have the car back by next week :D

Once I get it back then it is due for a full service, new pads. So that will be oil, filter, brake fluid, pads, coolant. Than swap the wheels and get it track ready :D

Krish are you running a hicas lock bar? Im gonna get one before the track day

Don't need to. Have had no issues with it yet so why bother with it.

I think I will be joining the beginer group as I have to trial a few different things :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...