Jump to content
SAU Community

Recommended Posts

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Blitz,

Yes can send the lines to WaggaWagga 2650.

They are probably not in the best shape, can't see any kinks, but not all straight. Postage via e-go will be approximately $20

So $30 all up. Probably wont be able to get them boxed and picked up till around Wednesday though (busy week ahead). Please note the Atessa unit is already sold.

See updated photo below.

IMG_1323.jpg

Sounds pretty fair , It's for a gtst but i'm guessing the gtr lines wont be that far off, if i find gtst ones before mid week i'll let you know.

Edit: Unlike the picture in the GTR service manual ,i'm now pretty sure they are nothing alike, the gtr lines go around to the rear side of the rack while the gtst lines goes pretty much on the front, Thanks anyway man

Edited by BLITZ9100

Sure do, I am home today and every night this week.

Send me a text or call me for address and to work out a time.

0404 010 832

Brad

Edited by Just_a_datsun

Sump sold.

Wiper motor/linkages sold pending payment.

Few parts are still remaining, few bits of plastics, pedals etc.

Triple gauges/centre plastic still available. $50

HalfcutParts26.jpg

Glovebox still available $20

HalfcutParts29.jpg

Will be had to contact this week.

  • 4 months later...

Ok guys, this stuff is taking a good m3 of shed space and I keep tripping over it, plus I now have another datsun taking up a bay of the shed so I need all the space I can get (should gave built that mezzanine).

So make an offer for all of it! I want it gone! I really don't want to pack anything anymore so pickup from enoggera.

Fan

http://i133.photobucket.com/albums/q63/garvice/48d64d16.jpg

A/C heat exchanger

http://i133.photobucket.com/albums/q63/garvice/33db9925.jpg

Triple gauges

http://i133.photobucket.com/albums/q63/garvice/fabc7dbb.jpg

Turbo compressor pipe

http://i133.photobucket.com/albums/q63/garvice/982a9504.jpg

Glovebox

http://i133.photobucket.com/albums/q63/garvice/95308917.jpg

Under dash plastic also got the fuse cover

http://i133.photobucket.com/albums/q63/garvice/21d4e258.jpg

Option steering wheel

http://i133.photobucket.com/albums/q63/garvice/8fbf4c1e.jpg

Saas gear knob

http://i133.photobucket.com/albums/q63/garvice/9bd8d061.jpg

Box of bits (hinges/plastics/pipes/wiper linkages and motor etc)

http://i133.photobucket.com/albums/q63/garvice/5586acf4.jpg

I want it all gone! Make me an offer!

Sorry Steve, didn't get notification of your post. Did you want the plastic centre console section that is surrounding the triple gauges too? Reason I ask is that the smaller it is the cheaper it will be to send. Send me a pm or text message oh4oh4oh1oh432 with your offer.

Brad

  • 2 weeks later...

Triple gauges gone but plastic console surrounding gauges still available.

Glovebox lock gone, but glove box plastic still available.

Come save these parts!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...