Jump to content
SAU Community

Recommended Posts

Sexy!

You've put a bit of work into that!

Another tip my engine builder suggested (but I'm not sure I'll bother with or not) is a splash guard I guess you would call it that deflects the oil dropping down from the oil returns in the head to the side of the block so it doesn't drop onto the crank which creates further drag and additional oil mist in the crankcase.

Makes sense I guess but where do you stop??

thanks, yea the cleanup work was done by my mate Grootie from Grooties Race and Resto in Adelaide.

the rb30 center returns hug the wall as you can see in the picture next to the bottom of the piston bores, and dont present as much as a problem as the rear galleries do, as the center area is a tornado of oil anyhow due to the spray from out of the sides of the bearings. the rear galleries however dump most of the oil back into the sump and on serious drag cars or circuit cars, presents an issue wh ere the oil is actually going back up those rear galleries, therefore not allowing the oil to flow down there fast enough. Those cards you were talkin about would be best placed there , we thought about doing it, but its a prick of a place to try and weld in some cards/baffles, but it can be done. I think it would present the best payoff/benifit, i guess, for the oil control issue in these RB motors

Im sure this has been done to death previously, and ps im not a mechanic, just a hobbyist.

cheers.

Sexy!

You've put a bit of work into that!

Another tip my engine builder suggested (but I'm not sure I'll bother with or not) is a splash guard I guess you would call it that deflects the oil dropping down from the oil returns in the head to the side of the block so it doesn't drop onto the crank which creates further drag and additional oil mist in the crankcase.

Makes sense I guess but where do you stop??

also called a windage tray.

thought about 2-3months after it was in the car, should have adapted the 26 windage trays to suit the 30.....

bah, next time...

  • 8 months later...

Sorry for bringing up an old thread but does anyone have more photos of exactly what holes to drill out so can do it before taking my block to the machine shop.

For the oil feeds, returns, or both?

also called a windage tray. (NO windage trays sit in the sump)

thought about 2-3months after it was in the car, should have adapted the 26 windage trays to suit the 30.....

bah, next time...

also called a windage tray. (NO . .the windage trays sit in the sump)

thought about 2-3months after it was in the car, should have adapted the 26 windage trays to suit the 30.....

bah, next time...

quoted for what reason?

and possibly about to do this in the following month.

Had trouble sending from my phone, hence the double post, but BEARING SPINNER was telling SHOOTA that "its called a windage tray" . . .but thats not what SHOOTA was talking about

a windage tray is in place to stop the crank from whipping up the oil in the sump(as it spins) and possibly away from the oil pickup

SHOOTA was asking about baffles that deflect the draining oil from dropping onto the crank

Had trouble sending from my phone, hence the double post, but BEARING SPINNER was telling SHOOTA that "its called a windage tray" . . .but thats not what SHOOTA was talking about

a windage tray is in place to stop the crank from whipping up the oil in the sump(as it spins) and possibly away from the oil pickup

SHOOTA was asking about baffles that deflect the draining oil from dropping onto the crank

ah, mis read it.

my bad.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...