Jump to content
SAU Community

Pin Code Security System

hitman_96

By hitman_96,
in Car Audio & Electrical

 Share

Recommended Posts

hitman_96 Apprentice

hitman_96

Posted
Posted

I'm sure most people on here are familiar with the car at the start of transporter 1. my question is regarding the car, when he gets in the car he has a security system with a PIN code which from what i can see, cuts out the power for the car and i was wondering if there if actually such a thing that exists/is available for purchase?

Link to comment
https://www.sau.com.au/forums/topic/376984-pin-code-security-system/
Share on other sites
XKLABA Grand Master

XKLABA

Posted
Posted

yes, i have one in each of my GTRs, there $300 -$400 fitted and cut three points( same as a normal alarm just with no siren), just not as fancy as the one in transporter just a key pad you enter a code into, some of the WRXs had to have them fitted as factory so they could get insurence, thanks to the ram raiders

jrm Veteran

jrm

Posted
Posted

The one that was used standard in WRX was provided by Brant, although their newer units have changed and are now essentially a South African immobilizer made by Sanji. Another retailer: http://carboncarsystems.com.au/sanji-zx40-wireless-keypad-immobiliser-p-154.html

They offer three point immobilization, auto-arms itself after you shut off the car, and has a handy valet mode (disables the unit temporarily - if someone drives the car for more than 15 minutes, next time the car is turned off, it automatically re-arms and requires a pin).

It typically is installed to operate completely independently of your regular alarm, giving you an extra layer of security. For the cost, it's probably not bad value in terms of the extra layer of protection.

Carbon 34 Grand Master

Carbon 34

Posted
Posted

thanks for all the help, is there any models that go from 0-9 instead of just 1-5, and is there any guides on fitting them?

thanks again.

there are lots better options available, RFID, Biometric ?

most house alarms arm based on 12V , so yes they make keypads with the digits you require. keypads automatic pin point a weak point in the alarm. they can follow the wires right back in ???

magnetic latching relays ?

RFID is 100% hidden. and you can make your car keyless.and just put in a start button..haha the keys stay in your pocket

Bio metric , can be as well.

just depends on your wallet and the skills of the installer?

danielr34 Collaborator

danielr34

Posted
Posted

Actually they cannot follow the wires back to the alarm module with the Sanji model. The wires on the keypad just go to +power and -earth and the communication link between the keypad and the keypad immobiliser module is done via these wires. They are from South Africa and so they have already thought of that about 5 years ago. Autowatch have a new version keypad immobiliser which incorporates a numeric remote control which you enter your pin number into and press send, which disarms the miniature immobiliser. The actual immobiliser is so small it can be concealed within a wiring harness.

Carbon 34 Grand Master

Carbon 34

Posted
Posted

Fyi :The sanji alarm is now wireless keypad , because people traced wires back !!!

But like a ATM cash machine I could sit back and use my long range camera lens to watch you input the code since it lights up at night ?? Too easy to get past

Keypad is out of date tech for low cost oem cars

Any decent installer should be able to foil even the best crims by mis information , alarms hooked to nothing ? The real one is hidden behind so many panels and even the keyswitch can be faked ??

And one the pressurize the abs brakes while armed ??

So much is possible it boggles the mind and wallet. Lol

Mind you this isn't a day job to install

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • oHBoy.
      Starter motor replacment teeth count.

      By oHBoy. · Posted

      I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...