Jump to content
SAU Community

Recommended Posts

Hi Brendan,

Their ROTA-Force - copies of the advan RS wheels haha

and thank you :)

Get off my thread both of you !!! spam.gif

HAHHAHAAAA.........Jonno your forgiven because I still need to pick up the cleaning stuff from you BEFORE you go overseas...Brendo - until we have another catch up session and talk for 4 hours about cars again your not forgiven !!

Christmas is the busiest time of the year for me as I work in hospitality....have been trying to get motivated to do car stuff but the 11 hour shifts 6 days a week are not making life any easier....

I have lots of tasks and little projects lined up.....but have to find the time to get started on them...and by the looks of it....not much is going to happen before new years.

This morning had other plans for me though....I woke up three hours earlier than I usually do and I had some spare time so decided to get my wiper blades changed - noticed the back one had become frayed and was "hanging" behind when the wiper was in use. This should explain what I mean

DSCN0686.jpg

Anyways..I changed them this morning and now have a new set of wiper blades :) Purposely left them a little longer than the last ones....so hopefully more of my windscreen will get cleaned..I remember having cut the front left extra short by accident last time round.

Also might quickly jot down some of the tasks that I have in mind...will tick them off slowly over the next few weeks

1. Paint calipers black and NISSAN writing in a nice red.....(should set off the gold and silver rims nicely and look a lot "healthier" than the grey old look they presently display)

2. Finish the window trims....(have left them sanded halfway....really need to get to this asap)

3. Build a ramp....and get the front of my car up...so that I can work on getting black mesh in front of the intercooler....(to make the front of the car look clean and stealthy)

4. Wrap a few hoses and fabricate a turbo shield.....(before I start melting stuff)

5. Get my rear bar heat proofed (just around the exhaust tip - flames look cool....but fire is HOT yes.gif)

6. Paint bits in the engine bay

7. Look into the sourcing of my new rims tongue.gif

Took the car up to the hills for a mid morning run....besides being bloody hot....it was awesome fun...some beautiful roads and views worship.gif

DSCN0746.jpg

DSCN0781.jpg

DSCN0726.jpg

Drive by video........................

Exhaust on idle video......................

Edited by jez NF

Just a heads up..............

Seems like a few people are having this problem (judging by the number or "reposts")

So if anyone tries to post in this thread...there is an error message that pops up when you click post....and it appears that your post has failed......dont worry..it usually comes through on the first go..........its strange (and annoying) and it happens to me all the time as well....just click forums or another of the tabs on top like I do after you click post and see the error message and then re-navigate to this page and you should see your post here yes.gif

and thanks.gif Lachlan

Edited by jez NF
  • 2 weeks later...

Today was another productive day.....

Went to Brendan's place for the day.....spent heaps of time chatting about car stuff as usual...had an awesome steak sandwich at the pub nearby...and trial fitted some wheels nyaanyaa.gif

Now part of the decision to change my rims was because of the fact that my current ones are 17 inches...I personally reckon they look too small and feel 18 inch rims are the sweet spot for skylines. Also mine have a decent offset but I have always wanted to run spacers just to get a more aggressive look. Brendo happens to have a very similar style to mine...but in 18s. They are shadow chrome (silver shade) or something like that...cant remember what he told me now...

SO....my options are...

1. Buy the rims from him and paint the middles gold like my current ones....

Advantages: Bigger dish on his ones....actual dish on the fronts as well....broader rims = wider tyres = I love the look from the back...no gutter rash on left hand side rims like mine.

Disadvantages: The offset on his are actually weaker..so will definitely have to run bolt on spacers

2. Buy the Te37s in Matte or Satin black

Advantages: I will finally have my much awaited black on black look...I can choose my offset and rim size etc

Disadvantages: Money honey

Opinions and suggestions welcome thanks.gif

Few pics to help people make a decision

Old versus "potential" new

DSCN0803.jpg

What his look like on my car (note: I will be changing the tyre profile...I like the meaty nascar look...so need more "tyre" on the rears)

DSCN0804.jpg

Driveway of win...rear view

DSCN0791.jpg

Driveway of win...front view

DSCN0796.jpg

Close up

DSCN0806.jpg

They have a much deeper dish look

DSCN0801.jpg

i think the silver rims look awesome. imho i really dont like the gold/silver ones you have at all. te37's are amazeballs, but if the silver ones you mate has can be bought at a sweet price, i say do it!! and PLEASE dont paint any part of them gold.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...